10040018 CITY OF CUPERTINO BUILDING PERMIT
BUILDING ADDRESS: 1697 GALWAY DR CONTRACTOR:M.D.CONSTRUCTION PERMIT NO: 10040018
OWNER'S NAME: PARRY MARTIN H AND JENNIFER A 334 TAIT AVE DATE ISSUED:04/05/2010
VNER'S PHONE: 4082192061 LOS GATOS,CA 95030 PHONE NO:(408)821-4755
❑ LICENSED CONTRACTOR'S DECLARATION BUILDING PERMIT INFO: BLDG I— ELECT[_ PLUMB F_
License Class Lic.# 7`y`i MECH r— RESIDENTIAL r— COMMERCIAL F_
Contractor M 0 Date Y/° �V
JOB DESCRIPTION:REMODEL(2)BACK TO BACK BATHROOMS;NON-
I hereby affirm that I am licensed under the provisions of Chapter 9 STRUCTURAL
(commencing with Section 7000)of Division 3 of the Business&Professions WORK REPLACE EXISTING FIXTURES LIKE FOR LIKE
Code and that my license is in full force and effect.
I hereby affirm under penalty of perjury one of the following two declarations:
I have and will maintain a certificate of consent to self-insure for Worker's
Compensation,as provided for by Section 3700 of the Labor Code,for the
performance of the work for which this permit is issued.
I have and will maintain Worker's Compensation Insurance,as provided for by
Section 3700 of the Labor Code,for the performance of the work for which this Sq.Ft Floor Area: Valuation:$20000
permit is issued.
APPLICANT CERTIFICATION APN Number:36624030.00 Occupancy Type:
I certify that I have read this application and state that the above information is
correct.I agree to comply with all city and county ordinances and state laws relating
to building construction,and hereby authorize representatives of this city to enter
upon the above mentioned property for inspection purposes. (We)agree to save PERMIT EXPIRES IF WORK IS NOT STARTED
indemnify and keep harmless the City of Cupertino against liabilities,judgments, WITHIN DAYS OF PERMIT ISSUANCE OR
costs,and expenses which may accrue against said City in consequence of the
granting of this permit. Additionally,the applicant understands and will comply 180 D OM LAST CALLED INSPECTION.
with all non-point source�regulationsperertino Municipal Code,Section
9.18.
� Issued by-
Ll
Date:
Signature Date l
L] OWNER-BUILDER DECLARATION RE-ROOFS:
I hereby affirm that I am exempt from the Contractor's License Law for one of All roofs shall be inspected prior to any roofing material being installed.If a roof is
the following two reasons: installed without first obtaining an inspection,I agree to remove all new materials for
I,as owner of the property,or my employees with wages as their sole compensation, inspection.
will do the work,and the structure is not intended or offered for sale(Sec.7044, Date:
Business&Professions Code) Signature of Applicant:
I,as owner of the property,am exclusively contracting with licensed contractors to
construct the project(Sec.7044,Business&Professions Code). ALL ROOF COVERINGS TO BE CLASS"A"OR BETTER
I hereby affirm under penalty of perjury one of the following three
declarations: HAZARDOUS MATERIALS DISCLOSURE
I have and will maintain a Certificate of Consent to self-insure for Worker's
Compensation,as provided for by Section 3700 of the Labor Code,for the I have read the hazardous materials requirements under Chapter 6.95 of the
performance of the work for which this permit is issued. California Health&Safety Code,Sections 25505,25533,and 25534. I will maintain
I have and will maintain Worker's Compensation Insurance,as provided for by compliance with the Cupertino Municipal Code,Chapter 9.12 and the Health&
Safety Code,Section 25532(a)should I store or handle hazardous material.
Section 3700 of the Labor Code,for the performance of the work for which this Additionally,should I use equipment or devices which emit hazardous air
permit is issued. contaminants as defined by the Bay Area Air Quality Management District I will
I certify that in the performance of the work for which this permit is issued,I shall maintain compliance with the Cupertino Municipal Code,Chapter 9.12 and the
not employ any person in any manner so as to become subject to the Worker's Health&Safety Code,Sections 25505,25533,and 25534.
Compensation laws of California. If,after making this certificate of exemption,I e
r ut or L ed �lt,, u
become subject to the Worker's Compensation provisions of the Labor Code,I must Owner
'GyDate: / lr/
forthwith comply with such provisions or this permit shall be deemed revoked.
CONSTRUCTION LENDING AGENCY
APPLICANT CERTIFICATION
I certify that I have read this application and state that the above information is I hereby affirm that there is a construction lending agency for the performance of work's
correct.I agree to comply with all city and county ordinances and state laws relating for which this permit is issued(Sec.3097,Civ C.)
to building construction,and hereby authorize representatives of this city to enter Lender's Name
upon the above mentioned property for inspection purposes.(We)agree to save
nify and keep harmless the City of Cupertino against liabilities,judgments, Lender's Address
and expenses which may accrue against said City in consequence of the
granting of this permit.Additionally,the applicant understands and will comply ARCHITECT'S DECLARATION
with all non-point source regulations per the Cupertino Municipal Code,Section
I understand my plans shall be used as public records.
9.18.
Signature Date Y/'�r(r'' Licensed Professional
CITY OF CUPERTINO
3 ITEMS OF 3 PERMIT RECEIPT OPERATOR: patg
COPY # 1
Sec: Twp: Rng: Sub: Blk: Lot :
APN . . . . . . . . : 36624030 . 00
DATE ISSUED. . . . . . . : 04/05/2010
RECEIPT # . . . . . . . . . BS000010092
REFERENCE ID # 10040018
SITE ADDRESS 1697 GALWAY DR
SUBDIVISION . . . . . . :
CITY CUPERTINO
IMPACT AREA . . . . . .
OWNER PARRY MARTIN H AND JENNIFER A
ADDRESS 1697 GALWAY DR
CITY/STATE/ZIP . CUPERTINO CA, CA 95014-5240
RECEIVED FROM M.D.CONSTRUCTION
CONTRACTOR . . . . . . . : MIKE DONAHUE LIC # 31172
COMPANY M.D. CONSTRUCTION
ADDRESS 334 TAIT AVE
CITY/STATE/ZIP . . . : LOS GATOS, CA 95030
TELEPHONE . . . . . . . . : (408) 821-4755
FEE ID UNIT QUANTITY AMOUNT PD-TO-DT THIS REC NEW BAL
---------- -------------
---------- ---------- -----
1BCBSC VALUATION 20, 000 . 00 1 . 00 0 .00 1. 00 0 . 00
1BSEISMICR VALUATION 20, 000 .00 2 . 00 0 . 00 2 . 00 0 . 00
1REMRESBAT SQ FEET 200 . 00 570 . 00 0 . 00 570 . 00 0 . 00
---------- ---------- ---------- ----------
TOTAL PERMIT 573 . 00 0 . 00 573 . 00 0 . 00
METHOD OF PAYMENT AMOUNT REFERENCE NUMBER
----------------- --------------- ---------------
CHECK 573 . 00 #1024
---------------
TOTAL RECEIPT 573 . 00
CITY OF CUPERTINO
ADDITION/REMODEL
CUPEi�TINO PERMIT APPLICATION FORM
Date:
Is a 2° unit being added? Yes ElNo ❑ If yes, please fill out the permit application for 2° unit.
Building Address:
Mailing Address (if different from building ad ress):
Phone#
Owner's Name:, : c�D�- a�`� - o2a 6/
Jcv\ ear
Contractor: Phone#: �p�- X01 l-`�7SS
Fax #:
Contractor License#: 7yy�s
Cupertino Business License#:
Contact: Phone#: /0 _ C I ?SS
/ � �
/1� � � Fax#:
Building Permit Info: Hillside ❑
Bldg. ❑ Elect. ❑ Plumb. ❑ Mech. ❑
Job Description: l
A4ditIMWhat is being added?(Be Specific): 4w- , xo
k"ry o vh S Nv h S 1
What is being remodeled (not including addition)?
Remodel Includes Re-Roof: Yes ❑ N If yes list number of squares
4
Remodel Includes Structural: Yes E] '
Do you have the pre-application planning approval? Yes ❑ No ❑
If yes, please provide a copy of your plannin a royal letter. Planners name:
Square Footage: Attached
Addition: Porch: Deck: Garage: Detached
ti
Remodel: Kitchen Bath va00 �} Other
Type of Construction (Usage Class): Occupancy Type:
1-A, 1-B ❑ IUIII/V-A ❑
IUIII B, IV-HT, V-B
Valuation: Please check this box if the project is a
O1110/ow V0 second-story addition ❑
Project Size: Express ❑ Standard ❑ Large ❑ Ma'or❑
Please complete relevant portion of the Green Building
Checklist & attach it to the application or if applicable, Green Building Points Achieved:
include in plan set & the sheet index.
***For Office Use Only*** Revised 07/06/09
Over-the-Counter ❑
CITY OF CUPERTINO
ADDITON/REMODEL
FEE SCHEDULE
Quantity Fee ID Fee Description Fee Group Permit Type
Sq Ft
DECKS 1R3SFDADD OR
1R3SFDREM
1DECKWOOD Deck (Wood)-Each B
(Each)
1 DECKRAIL Deck Railing-Each B
(Each)
GARAGES 1R3SFDADD OR
DETACHED 1R3SFDREM
1 GARDTW<=1 K Wood Frame up to B
1,000 SF (each)
1 GARDTM<=1 K Masonry up to 1,000 SF B
(each)
1 BCONSTAXR Construction Tax Res
(new detached garage)
PATIO'S OPEN 1R3SFDADD OR
1R3SFDREM
IPATIOWOOD Wood Frame up to 300 B
SF
1PATIOMETAL Metal Frame up to 300 B
SF
1PATIOOTHER Other Frame up to 300 SF B
PATIO'S CLOSED 1R3SFDADD OR
& SUN ROOMS 1R3SFDREM
IPATIOENCLW Enclosed Wood up to 300 B
SF
1PATIOENCLM Enclosed Metal up to 300 B
SF
1PATIOENCLO Other Enclosed Patio up B
to 300 SF
1 COVPORCH Porch Covered-Each B
(Each)
REMODELS 1R3SFDREM
1 REMRESKIT Kitchen Remodel up to B (Deduct "$"for ea plan
300 SF check
1REMRESBAT Bath Remodel up to 300 B 66
266 SF
1REMREOTH Other Remodel up to 300 B 66
SF
CITY OF CUPERTINO
ADDITON/REMODEL
FEE SCHEDULE
Quantity Fee ID Fee Description Fee Group Permit Type
Sq Ft
1 MECPLNCK Stand Alone Mechanical M
Pln Ck(hourly
1PLMPLNCK Stand Alone Plumbing P
Pln Ck (hourly)
1BCBSC Cal Bldg Standards B ALL PERMIT TYPES
Commission Fee
1BSEISMICRE Seismic Residential B
ITRAVDOC Travel &Documentation B
IBUSLIC Business License B
c
l . i
r
� � I
i
}t �
Y
� c �
�7
J
i
v
�C
i�
-: tt
:_ _--- m designs The requirements listed are
_�
- summary guide does not cover all pothebubding permit and the inspections oft e war
This
the minimum standards for issuance of
Code)
Bu
i]din Ree uirementS (2007 California Building .
sum Board in Showers and Water Closet CBC 250 . with manufactur ceiling
panels in
1) G sum backers insta
fled in accordance
fiber-cement or glass mat gyp
Cement, abase for wall file in tub and shower areas and wall an
recommendations shall be used as
shower area. eats CBC 2509.2
2) G sum Board in
Water Closet Com artm compartment walls,
board shall be used as a base for file in water closet cam
Water-resistant gypsum
backing recommendations.
installed in accordance with manufaeturera inu'tattons CBC 2509.3
sum Backfin Boar
3) Wa71
ter-resistant G locations: ]Z
the following
Shall not be used in artrrlent. such as
a) Over a vapor retarder in shower or bathroom comp subject to continuous high humidity
there will be direct exposure to water or in areas BY.
b) Where ll sum board
steam room or sauna room• xeeeds board.
C) On ceilings where frame spacing
e 12 inches on center for '/s"ttthick water-resistant gypsum
e than 16 inches on center for 518"thick water resistant gyp
or
more CBC 2509.2
4) G sum Board in Rest of Bathroom
le or wall panel in other wall and ceiling areas.
Regular gypsum board is petted under ti
Cement Backer!Fiber cement Backer!
nt Underlayment Thinset'
--_ pensBhielcr Tile Backer*
Fiber Ceme i
= Ceramic Tile I
Ceramic Tile Thinset Method
pryseI or Latex-Partland Cement or Fiber Cement
« ' Cement Mortar "" =� Backer Unit(CBU)o'
or Or anis Adhesive Fiber Cemenl_`°yr"enl
t
Cooled Glass Mat 1 Membrane Required
in We
F Water-Resistant Gypsum t t Areas
I
Backer Board
{. 1
} x (Dens5hield'Tile Backer ' Wed or Meiol Studs
_ Wood or Metol Studs
f �
- For use irr wet or dna areas u ores only.
>• _ areas manufacture's
products:examples shown are for illustration p rP
For erse�t«t or dry specific manufa Revised 1/27/1
Note_The City of Santa Clara does not endorse in t ents 01-2010.doe
1:\BLW\Fn4A'IFORMS\A-lnformationaAAS Rcsidcntial Bathroo
Plumbing Requirements (2007 California Plumbing Code)
1) Shower Drain &Trap
2 inches minimum. (CPC Table 7-3)
2) Shower Compartments
a) Minimum interior of 1024 square inches.
b) Minimum dimensions so a 30-inch circle will fit in the compartment.
c) Minimum height above floor drain is 70 inches.
d) Shower doors shall open to provide a minimum of 22 inches unobstructed egress opening
3) On Site Shower Pan (Receptor)
On ground type, shall be water tight, constructed with approved material,adequately reinforced and with an
approved flange floor drain. Lining to be pitched t/4"per foot to weep holes in drain. (CPC 411.8 (1))
Above ground type,water tight lining with minimum of 3 inches above finished dam,curb or threshold
height. In no case shall any dam or threshold be less than 2 inches or more than 9 inches in depth when
measured from the top of the dam or threshold to the top of the drain. (CPC 411.5 and CPC 411.6)
4) Shower and Tub-Shower Control Valves
Control valves shall be pressure balance,thermostatic, or combination of pressure balance/thermostatic
mixing valves. Handle position stops shall be provided on such valves and shall be adjusted per the
manufacturer's instructions to deliver a maximum mixed water setting of 120 OF. (CPC 418.0)
I30"Minimum
' (762 mm)
LINING MATERIAL
30"Minimum
762 mm _— NAILING 70 BE A ftINIMU'.t
OF 1-425.4—1 ADOvE FmismrD OA%
Oa THRESHOLD
Y'126,2 rlrnJ IFUR OUT OR NOTCJI
1024 Sq.In. -------STUDSGJ RECEIVE
fMinimum -
I `
/
APPROVED TYPE SUBDRAIN
I:\BLDG\FINAL\FORMS\A-Informationa1W85 Residential Bathroom Requirements 01-2010.doc
Revised 1'27!10.
Electrical Requirements (2007 California Electrical Code)
1) At least one receptacle must be installed within a residential bathroom within 3 feet of the sink and(See
Figure 1):
a) On the wall adjacent to the sink; or,
b) On the side or face of the sink cabinet.
2) Bathroom receptacles shall be install on a 20-ampere branch circuit that is (See Figure 2):
a) Dedicated to only bathroom receptacles; or,
b) Dedicated to the receptacles and lighting within a single bathroom only.
General rule:Receptacle outlets)supplied by at
At least one wall receptacle outlet within 900 mm least one 20 ampere branch circuit.
(3 ft)of outside edge of each basin. Such circuits shall have no other outlets.
CDOutside edge
Exception permits other equipment within same
Optional location of single receptacle centered between bathroom to be supplied by 20-ampere branch
the sinks and within 900 mm(3 ft)of either sink circuit where it supplies one bathroom only.
Figure 1 Egure
3) Ground-Fault Circuit-Interrupter protection is require for all bathroom receptacles.
4) Receptacles may not be installed within or directly over a bathtub or shower stall (See Figure 3).
TA
. _
kl--"'erl�7 i
I �
7
Receptacles not permitted within or directly over bathtub or shower space
Figure 3
I:\BLDG\FINAL\FORMS\A-Infonnational\A85 Residential Bathroom Requirements 01-2010.doc
Revised 127/10
T24 Energy Requirements (2008 Building Energy Efficiency Standards and ASHRAE 62.2)
1. Lighting Requirements:
a. Permanently installed light fixture in bathrooms shall be High-efficacy luminaires. Low-efficacy
luminaires are allowed if they are controlled by a manual-on occupancy sensor.
b. Occupancy sensor must be manual on/off and automatic off.The maximum time delay to turn off is 30
minutes after the last detected motion. Sensors cannot have an override allowing the light fixture to be
continuously on.
c. High-efficacy and Low-efficacy light fixtures must be controlled separately.
d. Exhaust fans with integral lighting system shall be switches separately from lighting system OR have a
lighting system that can be manually turned on and off while allowing the fan to continue to operate for
an extended period of time. Lighting integral to an exhaust fan must be high-efficacy.
e. Permanently installed night light must be high efficacy lighting OR the night light is rated to consume
no more than 5 watts of power and does not contain a medium screw-base socket.
2. Bathroom Ventilation Requirements:
The Mandatory Measures, Section 150-(o)is NEW for the 2008 Energy Standards. These mandatory measures
required that low-rise residential buildings meet the requirements of ASHRAE Standard 62.2 for"Indoor Air
Quality and Mechanical Ventilation". This is a health and safety measure developed by ASHRAE to ensure
that dwelling units have acceptable indoor air quality.
When Required?
It is mandated for all newly-constructed low-rise residential buildings(up to 3 stories) and additions greater
than 1,000 square feet(original building must also comply).
Local Exhaust Ventilation in Bathroom and Kitchen
a. Each bathroom is required to have a 50 cfm. minimum exhaust fan ducted to the outside. Bathroom is
any room with a bathtub, shower, spa or similar sources of moisture. Toilet room is not considered a
bathroom.
b. The ducting for the exhaust fan shall be sized accordance to ASHRAE Standard 62.2, Table 7.1.
c. Local exhaust fans are required to be rated for sound at a maximum of 3 sones, unless their maximum
rated airflow exceeds 400 cfin.
I:IBLDGIFINAL\FORMS\A-InformationahA85 Residential Bathroom Requirements 01-2010.doc
Revised 1/27/10
GYPSUM BOARD AND PLASTER
ishes or any similar application that would be equiva- by
partitions.
a t it io force resisting elements ction of hall be designed ceiling to the eand
rti-
lent to joint treatment.
2. On single-layer systems where joints occur over
detailed to transfer lateral forces.
wood framing members.
3. Square edge or tongue-and-groove edge gypsum SECTION 2509
board (V-edge), gypsum backing board or gypsum GYPSUM BOARD IN SHOWERS AND WATER
sheathing. CLOSETS
4. On multilayer systems where the joints of adjacent
areas.Showers and public toilet walls shall con-
layers are offset from one to another. 2509.1 Wet
5. Assemblies tested without joint treatment.
form to Sections 1210.2 and 1210.3.
2508.5 Horizontal gypsum board diaphragm ceilings.Gyp- 2509.2 Base for tile.Cement,fiber-cement or glass mat gyp-
sum board shall be permitted to be used on wood joists to create sum backers in compliance with ASTM C 1178,C 1288 or C
a horizontal diaphragm ceiling in accordance with Table 1325 and installed in accordance with manufacturer recom-
2508.5. mendations shall be used as a base for wall tile in tub and
proportions.The maximum mow_ shower areas and wall and ceiling panels in shower areas.
25085.1 Diaphragm Water-resistant gypsum backing board shall be used as a base
able diaphragm proportions shall be 1'/2:1 between shear for tile in water closet compartment walls when installed in
resisting elements. Rotation or cantilever conditions shall accordance with GA-216 or ASTM C 840 and manufacturer
not be permitted. recommendations. Regular gypsum wallboard is permitted
25085.2 Installation.Gypsum board used in a horizontal under tile or wall panels in other wall and ceiling areas when
diaphragm ceiling shall be installed perpendicular to ceiling installed in accordance with GA-216 or ASTM C 840.
framing members.End joints of adjacent courses of gypsum 25093 Limitations. Water-resistant gypsum backing board
board shall not occur on the same joist. shall not be used in the following locations:
2508.5.3 Blocking of perimeter edges.All perimeter edges 1. Over a vapor retarder in shower or bathtub compart-
shall be blocked using a wood member not less than 2-inch menu.
by 6-inch(51 mm by 159 mm)nominal dimension.Block-
ing material shall be installed flat over the top plate of the 2. Where there will be direct exposure to water or in areas
wall to provide a nailing surface not less than 2 inches(51 subject to continuous high humidity.
mm)in width for the attachment of the gypsum board. 3. On ceilings where frame spacing exceeds 12 inches(305
25085.4 Fasteners. Fasteners used for the attachment of mm) o.c. for '/Z inch-thick (12.7 mm) water-resistant
gypsum board to a horizontal diaphragm ceiling shall be as gypsum backing board and more than 16 inches (406
defined in Table 2508.5.Fasteners shall be spaced not more mm) o.c. for 5/8-inch-thick (15.9 mm) water-resistant
than 7 inches (178 mm) on center (o.c.) at all supports, gypsum backing board, _ >
including perimeter blocking, and not more than 3/s inch
(9.5 mm)from the edges and ends of the gypsum board. SECTION 2510
250855 Lateral force restrictions. Gypsum board shall FOR
-
imposed
be used in diaphragm ceilings to resist lateral forces CEMENT PLATHING AM11RERRING RING Fps CR
imposed by masonry or concrete construction.
oT
2508.5.6 Diaphragm ceiling connection to partitions. 2510.1 General.Exterior and interior cement plaster and lath-
[DSA-SS&OSHPD 1 and 4]Gypsum board shall not be ing shall be done with the appropriate materials listed in Table
used in diaphragm ceilings to resist lateral forces imposed 2507.2 and Chapter 35.
TABLE 2508.5
SHEAR CAPACITY FOR HORIZONTAL WOOD FRAMED GYPSUM BOARD DIAPHRAGM CEILING ASSEMBLIES
THICKNESS OF MATERIAL SPACING OF FRAMING SHEAR VALUE"'
(MINIMUM) MEMBERS(MAXIMUM)
MATERIAL (inches) (inches) (PHof ceiling) MINIMUM FASTENER SIZE
5d cooler or wallboard nail;
Gypsum board '/z 16 O.C. 90 15/8-inch long;0.086-inch shank;
G
YP i5/ -inch head
5d cooler or wallboard nail;
G 1/2 24 o.c. 70 15/,-inch long;0.086-inch shank;
Gypsum board 'I/,,-inch head`
For SI: 1 inch=25.4 mm,1 pound per foot=14.59 N/m.
a. Values are not cumulative with other horizontal diaphragm values and are for short-term loading due to wind or seismic loading.Values shall be reduced 25 percent
for normal loading.
b. Values shall be reduced 50 percent in Seismic Design Categories D.E and F.
c. 1 1/4 inch,No.6 Type S or W screws are permitted to be substituted for the listed nails.
2007 CALIFORNIA BUILDING CODE
386
Community Development
10300 Torre Avenue
;x
Cupertino CA 95014
Telephone(408) 777-3228
U CITY Of Fax(408) 777-3333
DT
Building Department
All Cupertino building permits must meet certain conditions related to maintaining
environmental quality and public peace and safety. The two most common
conditions are described below.
STORMWATER POLLUTION CONTROL
State law requires that Cupertino, 12 other Silicon Valley cities, Santa Clara County and
the Santa Clara Valley Water District control stormwater pollution. Educating local
residents and businesses and enforcing stormwater pollution control laws are key parts
of the City's compliance efforts.
Stormwater pollution prevention: It's up to us
In northern Santa Clara Valley, storm drains flow directly to local creeks and San
Francisco Bay, with no treatment. Stormwater pollution is a serious problem for wildlife
dependent on our waterways, for people living near streams and baylands, and for the
local water supply. Common sources of stormwater pollution include:
• Dripped oil, fuel, and antifreeze from vehicles and heavy equipment;
• Construction debris, including dirt, concrete and paint;
• Landscaping runoff containing pesticides or weed killers; and
• Any material dumped or spilled into streets or storm drains
The property owner and the contractor share ultimate responsibility for activities
occurring at a construction site and will be held responsible for any environmental
damage caused by subcontractors or employees.
For more information on construction-related stormwater requirements, see the
Stormwater Quality Regulations section of the City of Cupertino web site at:
httr)://www.cur)ertino.org/city government/departments and offices/
environmental services
COMMUNITY NOISE CONTROL
The basic noise control requirements for construction sites are as follows:
• Typical construction work hours are:
- Weekdays — 7 a.m. to 8 p.m.
- Weekends — 9 a.m. to 6 p.m.
• Construction other than street construction is prohibited on holidays.
• Residential daytime noise levels from complaint qRap�- 60 dBA
• Nonresidential daytime noise levels from complaint
For more information on noise control, please see Chapter 10.48 of the Cupertino
Municipal Code, which can be accessed at httr)://www.amlegal.com/cupertino ca/
Greg Casteel
Building Official
Building Department
City Of Cupertino
10300 Torre Avenue
Cupertino, CA 95014-3255
Telephone: 408-777-3228
C U P E RT I N O Fax: 408-777-3333
CONTRACTOR/ SUBCONTRACTOR LIST
JOB ADDRESS: %6V PERMIT# Ioc`P"
OWNER'S NAME: H' PHONE #
GENERAL CONTRACTOR: 14,(x_ Otis -t BUSINESS LICENSE# 3117L
ADDRESS: S3-( T---t CITY/ZIPCODE:
*Our municipal code requires all businesses working in the city to have a City of Cupertino business license.
NO BUILDING FINAL OR FINAL OCCUPANCY INSPECTION(S) WILL BE SCHEDULED UNTIL THE
GENERAL CONTRACTOR AND ALL SUBCONTRA RS HAVE OBTAINED A CITY OF CUPERTINO
BUSINESS LICENSE.
I am not using any subcontractors: —� Date
Signature
Please check applicable subcontractors and complete the following information:
SUBCONTRACTOR BUSINESS NAME BUSINESS LICENSE #
Cabinets & Millwork
Cement Finishing
Electrical
Excavation
Fencing
Flooring/ Carpeting
Linoleum/Wood
Glass/ Glazing
Heating
Insulation
Landscaping
Lathing
Masonry
Painting/Wallpaper
Paving
Plastering
Plumbing
Roofing
Septic Tank
Sheet Metal
Sheet Rock
Tile
Owner/Contractor Signature Date