B-2016-1593CITY OF CUPERTINO BUILDING PERMIT
BUILDING ADDRESS:
1103 KENTWOOD AVE CUPERTINO, CA 95014-5807 (359 31 001)
OWNER'S NAME: SATHE SAMIR AND VAISHALI TRUSTEE
OWNER'S PHONE: 408-505-3099
LICENSED CONTRACTOR'S DECLARATION
License Class B Lic. #832709
Contractor NEWHOME CONSTRUCTION Date 02/28/2018
I hereby affirm that I am licensed under the provisions of Chapter 9 (commencing
with Section 7000) of Division 3 of the Business & Professions Code and that my
license is in full force and effect.
I hereby affirm under penalty of perjury one of the following two declarations:
t. I have and will maintain a certificate of consent to self -insure for Worker's
Compensation, as provided for by Section 3700 of the Labor Code, for the
performance of the work for which this permit is issued.
I have and will maintain Worker's Compensation Insurance, as provided for by
V Section 3700 of the Labor Code, for the performance of the work for which this
permit is issued.
APPLICANT CERTIFICATION
I certify that I have read this application and state that the above
information is correct. I agree to comply with all city and county ordinances
and state laws relating to building construction, and hereby authorize
representatives of this city to enter upon the above mentioned property for
inspection purposes. (We) agree to save indemnify and keep harmless the
City of Cupertino against liabilities, judgments, costs, and expenses which
may accrue against said City in consequence of the granting of this permit.
Additionally, the applicant understands air ill comply with all non -point
source regulations per the Cupertin -M n� 1Zode, Section.
Signature a 5/19/2016
OWNER -BUILDER DECLARATION
I hereby affirm that I am exempt from the Contractor's License Law for one of the
following two reasons:
1. I, as owner of the property, or my employees with wages as their sole
compensation, will do the work, and the structure is not intended or offered for
sale (Sec.7044, Business & Professions Code)
2. I, as owner of the property, am exclusively contracting with licensed
contractors to construct the project (Sec.7044, Business & Professions Code).
I hereby affirm under penalty of perjury one of the following three declarations:
1. I have and will maintain a Certificate of Consent to self -insure for Worker's
Compensation, as provided for by Section 3700 of the Labor Code, for the
performance of the work for which this permit is issued.
2. I have and will maintain Worker's Compensation Insurance, as provided for by
Section 3700 of the Labor Code, for the performance of the work for which this
permit is issued.
s. I certify that in the performance of the work for which this permit is issued, I
shall not employ any person in any manner so as to become subject to the
Worker's Compensation laws of California. If, after making this certificate of
exemption, I become subject to the Worker's Compensation provisions of the
Labor Code, I must forthwith comply with such provisions or this permit shall
be deemed revoked.
APPLICANT CERTIFICATION
I certify that I have read this application and state that the above information is
correct. I agree to comply with all city and county ordinances and state laws
relating to building construction, and hereby authorize representatives of this city
to enter upon the above mentioned property for inspection purposes. (We) agree
to save indemnify and keep harmless the City of Cupertino against liabilities,
judgments, costs, and expenses which may accrue against said City in
consequence of the granting of this parmit. Additionally, the applicant understands
and will comply with all non -point source regulations 'per the Cupertino Municipal
Code, Section 9.18.
CONTRACTOR: PERMIT NO: B-2016-1593
NEWHOME
CONSTRUCTION
FREMONT, CA 94539
DATE ISSUED: 05/19/2016
PHONE NO: (408) 421-9808
BUILDING PERMIT INFO:
X BLDG —ELECT —PLUMB
X MECH X RESIDENTIAL _ COMMERCIAL
JOB DESCRIPTION:
CONSTRUCT FRONT OFFICE ADDITION (96 SQ FT) WITH
COVERED PORCH (39 SQ FT); REAR BEDROOM ADDITION (368 SQ
FT); INTERIOR REMODEL (957 SQ FT); RELOCATE FURNACE TO
GARAGE.
Sq. Ft Floor Area: 1006 Valuation: $92000.00
APN Number: Occupancy Type:
359 31 001 Deferred Submittal (R -3),R-3 (Custom)
PERMIT EXPIRES IF WORK IS NOT STARTED
WITHIN 180 DAYS OF PERMIT ISSUANCE OR
180 DAYS FROM LAST CALLED INSPECTION.
Issued by: Abby yende Cu&\ Qd,l„p�,,,.4 2
Date: 05/19/2016 "�`� �`�(
RE -ROOFS:
All roofs shall be inspected prior to any roofing material being installed. If a roof is
installed without first obtaining an inspection, I agree to remove all new materials for
inspection.
Signature of Applicant:
Date: 5/19/2016
ALL ROOF COVERINGS TO BE CLASS "A" OR BETTER
HAZARDOUS MATERIALS DISCLOSURE
I have read the hazardous materials requirements under Chapter 6.95 of the
California Health & Safety Code, Sections 25505, 25533, and 25534. I will
maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and the
Health & Safety Code, Section 25532(a) should I store or handle hazardous
material. Additionally, should I use equipment or devices which emit hazardous
air contaminants as defined by the Bay Area Air Quality Management District I
will maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and
the Health &Safety Code, Sectio 55– 533, a 34.
Owner or authorized agent:
Date: 5/19/2016
CONS RUCTION LENDING AGENCY
I hereby affirm that there is a construction lending agency for the performance
of work's for which this permit is issued (Sec. 3097, Civ C.)
Lender's Name
Lender's Address
ARCHITECT'S DECLARATION
I understand my plans shall be used as public records.
Licensed
Signature Date 5/19/2016 Professional
CiUPERTINO
CONSTRUCTION PERMIT APPLICATION
COMMUNITY DEVELOPMENT DEPARTMENT - BUILDING DIVISION
10300 TORRE AVENUE • CUPERTINO, CA 95014-3255 •
(408) 777-3228 • FAX (408) 777-3333 • buildin (a�cupertino.orq "3 -lou p
❑ I.TEW CONSTRUCTION ER ADDITION ❑ ALTERATION 1 TI ❑ REVISION I DEFERRED ORIGIATAL PERMIT ff
PROSECT ADDRESS { 1 0'3 V JF*'T r tVL) NZ(V,
7A.PN# t� + o o. -L
MhVERNAME (� y11� [��-CLt PHOT O ci' �OS ~3� EMAIL
�A-M1�:_SATit��' y�l�tno,ca
STREET ADDRESS CITY, STATE, ZIP FAX
V15TW1300 i�.m C& 1,3D1
CONTACT NAME ,'1V '��t� PHO. v�,---
fi '�
STREET ADDRESS CITY, STATE, ZIP FAX
*4 L541� +Von ST• I �nI�yr X115°.
❑ 01AWER ❑ OAN'ER-BUILDER ❑ OWNERAGENT IJ CONTRACTOR ❑ CONTRACTORAGENT Cl ARCHITECT ❑ ENGINEER ❑ DEVELOPER ❑ TENANT
CONTTRACTORNAME LICENSENUMBER LICENSETRPE
BUS.LICR
COMPANY NAME
E-MAIL
FAX
STREET ADDRESS
CITY, STATE, ZIP
PHONE
ARCHITECTIENGINEERNAME LICENSE NUMBER
BUS, LTC R
COMPANY NAME E-MAIL
FAX
STREETADDRESS !T CITY, STATE, ZIP
PHONE
DESCRIPTION OF WORK
uro
'VSTA a..
EXISTINGUSE PROPOSEDUSE CONSTR.
TYPE STORIES
d•�
USE TYPE I
j
OCC.
SQFr
VALUATION (S)
DaSTG
NFW FLOOR
DEMO
TOTAL
AREA
AREA $b
AREA
NET AREA
BATHROOM KITCHEN
OTHER
REMODBLAREA REMODELAREA
I
REMODEL AREA
PORCH AREA
DECK. AREA
TOTAL DECKMORCH AREA
GARAGE AREA; LJ DETACH
❑ ATTACH
I
e DWELLING UNITS:
SECOND USIT ❑YES
SECOND STORY _]YES
j
FBsilr
SD
NGADD? []NO
DITION? NO
ADi]
I
Ij
PRE :APPLICATION YES IF ]'FS, PROVIDE COPY OF
❑
IS THE BLDG A\ I -ES
❑
EI4 B ' - ' Ms�`5.':.'r?};`: •` '`I
;:'-s .- "` `-
` - °j:'=+
�`^r;<r. ;r:;n;,f.a,�•;
�- .,,.:,�-1. 11'1,
_ ,
T \ALL ATI ON:
Pt.AKNW-GAPPLO []NG PLANNING APPROVAL LETTER
MCHLER HOPTE? ❑ NO
•`^ ' - z-:� :*`S -i:
+'"- i'''
By my signature below, I certify to each of the following: I atn the property owner or authorized agent lo act ok the property owner's behalf. I have read this
.application and the information I have ' vided is carrect. Iwe read the es ription of 1T,?ork and vcrify it is accurate. I agree to coinply with all applicable local
ordinances and state laws relatiDg to ildi g construction.. a onze rel - se tatives of Cupertino to enter the above -identified propertyfor inspection purposes.
Signature of Applicant/Agent:T Date:
SUPPLEMENTAL 1TTFORIvIATT01\ I REQUIRED
471Ot,rir+,t:'.�x,:L.:rk+':'�'--y rYiiir''Y::�r%:-+E�"=_-cb;{�i�4�•,ym.:;�3=[^7`u:f.Str�:?i4-'•;::jli':.Y3;1
S�CH'
1.
�.ti`.t"
-12 T.SLiPafE;`` ,
IIIGECT
New SFD or Muldf'anul dwellings: Apply for demolition permit for
/
existing buildings Demolition ennit is re uired prior to issuance of building
} 1? tl P
"?}� ^.Sit= fi41'?._ ..`='mow eriT.
� _ "-`• �"--�'^` �. '�_ �•
?•, �:r't,T. _ TF�T.E COLITER �4$U
Fn
l�'U'4- 3qr ��','�•rti"`-`t'�:r''.'r"a'G:\.:'.�v�v'c�.���_�%{:Yf
_ -
eLDL\GY,L:4\$\IE��I",��� W,
S�
rs
pen -nit o al . e
for new buildin
n txq Yfic aru y� ax }
i`'F
rRM
� '1
rF�����crLA}I.IZyE�
j7 -rt'.tY.:'adl.s,✓�\��r�[2�L
;+^Vj-'�"�
_ Commercial Bldgs: Provide a completed Hazardous Materials Disclosure
forin if being
,L�srA�ARo t r
...'ggg
bBLtCja ORhSt '�, st+
any Hazardous Materials are used as part of this project.
n LGEF
1
zE.i�e�?a-er>
Letter
r~ �(k
`�� F�
_ Copy of Planning Approval or Meeting With Planning prior to
r� :yY���',
; '• `-i _;,
L1fT:AR1.SEli ER_ ISTRl T -i%'
I submittal of Building Permit application.
i.`;rnL470iL w:C=
�;•Ir,•:;�-���;_�[,;;^�,;;;,;'�'���`•
�S. ,
:s::�==>^.�rs�:^��. ".-FI
ire+ d -r f%r�.J
;'
7t : �'a. >,k ;: L.: ;aa- ? ; ., _ •.
rvtz ,Tt:.
F'ENVIRO\\4E1 I 4t HEALTH i=°°,'':•-
�`l�6LS
B1d&4pp_2011.doc revised 06/21/11
Reviewed By: Sean Hatch
Date: 05/11/16
I TABLE OF CONTENTS I
Cover Page 1
Table of Contents 2
Form CF -1 R -PRF -01 -E Certificate of Compliance 3
Form RMS -1 Residential Measures Summary 11
Form MF -1R Mandatory Measures Summary 12
Room Load Summary 16
CUPERTINO
Building Department
EnergyPro 6.7 by EnergySoft REVIEWER fGgc-COUB(C-01 kPLIANCE User Number: 6249
Reviewed By: Sean Hatch
Date: 05/11/16
CD
aD
v
0
z
3
:s
7J 2
(D m
O AVi
G) o
(D <
7 Q
D N
v ..
!D
Q
v
N
O
N
Ql
O
W
W
0
N
w
w
o
n
O
9
M
r
w
N
o
a
z
n
m
O
dD
O
m
N
O
dD
O
N
c
W
N
0
w
N
c
N
N
N
a
a
a
D
y
y
c
7
o
p
m
-p
N
O
Z
at
N
O
3
n
o
c
O
m
O
`D
n
m
a
m
m
v
m
=
O
m
01
n
w
y
p
yv
�
T
O)
O
—
c
m
N
N
3
T
7
CO
CO
CD,
C
P
ER
B
FOR
ild
CODE
ng
D
C
01
�
N
w
O
>
of
OD
1
N
W
y
a
J
4
a
o
U'
cn
J
N
0
m
a
O
o
N
c
7
3
7
O
0
P-
m
Z
M
ui
m
N
C
M
W
7
0
0
5.
O
v
o
T
c
a
a
a
w
a
O
m
N
r
�
C
01
01
01
CO
01
13
'1
w
O
w
N
[0
O
OD
_
o
K
J
U)
0
O
A
O
CNO
Q
>
A
O
A
O
O
O
<O
No
J
cf)
A
03 W
0
1
70
N
n
cQ
o
m
N
7
n
O
O
O
O
O
6
O
�.
O
O
O
�O
W
n
O
V
N
01
o
°o
c�
C4
D
(n
n
7
N
N
(Q
w
n
o'
01
V
o
V
Oo
Oo
0
M
13
Co
0
0
0
0
-.o
C
T
O
0
3
O
.3+
Z
C
O
R
W
Reviewed By: Sean Hatch
Date: 05/11/16
5 n
-0 m
c �
21 a1
F 0
a1 :3
fD
Cn
¢F1
3 N
Q
Q' O
Q• N
7 Cn
X C
P
W
N
O
y
0
1
M
m
1 M
0 71
� 0
O 1
n
O
9
M
r
w
N
o
a
z
n
m
O
dD
O
m
N
O
dD
O
N
c
W
N
�
Z
N
c
N
c
Q
�
N
a
a
o
m
m
7
o
p
m
-p
N
O
Z
at
N
O
3
n
o
c
O
O
`D
a
o
m
m
v
�
N
I
o
3
r
w
y
m
T
O)
p
�
z
c
m
N
N
3
T
CD,
C
P
ER
B
FOR
ild
CODE
ng
D
C
E
Reviewed By: Sean Hatch
Date: 05/11/16
5 n
-0 m
c �
21 a1
F 0
a1 :3
fD
Cn
¢F1
3 N
Q
Q' O
Q• N
7 Cn
X C
P
W
N
O
y
0
1
M
m
1 M
0 71
� 0
O 1
O
dD
O
A
N
O
dD
O
A
W
N
�
Z
m
a
r
z
T
O
O
>
of
Z
a
a
w
a
O
o
c
7
3
O
0
P-
M
ui
Q
N
C
M
W
7
0
0
5.
-
v
o
T
a
a
a
w
a
O
N
r
01
01
01
CO
01
13
'1
w
w
w
N
[0
Z
a
o
K
o
o
0
O
O
No
n
cf)
C)
0
1
70
n
cQ
o
m
N
o
D
�.
3
o
°o
c�
D
D
(n
n
N
N
(Q
w
o'
V
M
V
N
W
M
N
T
O
0
O
.3+
Z
C
O
<D
O
Z
N
c
Z
O.
01
N
Z
O
O
y
w
'
a
a
01
p
=
�? o
Q
a
Oto
.3+
N
O)
COOLI
O
N
Q
(D
O
C
a_
-
7
N
N
0
01
N
N
Co
C)
1
U7
j
m
o
N
03
N
O
0
�
�
N
N
�
O
L
W
A
J
A
A
N
rtnler
t
PLI
N
E
Reviewed By: Sean Hatch
Date: 05/11/16
5 n
-0 m
c �
21 a1
F 0
a1 :3
fD
Cn
¢F1
3 N
Q
Q' O
Q• N
7 Cn
X C
P
W
N
O
y
0
1
M
m
1 M
0 71
� 0
O 1
CD
O
z
3
cy-
;;o x
(D m
O V)
) O
(D G
7 Q
CD
v ..
CD
Q
N
N
O
Ql
O
W
W
O
N
w
w
Reviewed By: Sean Hatch
Date: 05/11/16
o < O c
--i
3
O --1 --1
m
N
o
L
z
N
O
<N
M
FID l. CRD
z
.+ N m
C
0
o a
m
r
XT
6
�
TI
N
cn
N N
3
w
N
w
fD C N
3
7D
R
cQ
m
m
z
7 N
= o
(n N
a
Q
o3 3
to
s
7
(On N
o p' j
O
O
7 7
Z
p
7
7
6
N
7
7
�
N
n
Q
Q
�
7
m'
n
2
_
=
a
D
D
n�
�
m'
Q
C7
C7
c
m
Cn
Cn
x
�
O c
m
3
m
3
z
N -O
7
w
(n O
n
O
7 7
O_
O p
O
7
N
3
O
N
N
m
7
mc
Ko
fD
m
m
0)
v,
c
o
N
v
O
A
J
N
O
a
7
N
N -0
cQ
m
fD
N O
D)
A 7
m
7
N
7
C
G
0
0
�
Co
O0
0
c
m
c �-
D1
7
(n �.
Q
o m
OQ
3-0
O
ent
fD
O
p
p
2
22C
�
C2
C
<
m
w m
Cn
CnN
3
O
C
fD
N o
(n
N
N -
w
fD
N
O
r
3
J
3
O
3 O
D)
�D
fD
7
n
n O
O+
7. N
O
V
0 Cf)
�
N N
c
7 7
O_ 0-
N
N Q
0
o p
N
fD
w
=3
.� �.
j
J
7
(a Co
3
N
Reviewed By: Sean Hatch
Date: 05/11/16
o < O c
--i
3
O --1 --1
m
° �D
o
L
z
N
O N O O 3 0 7
oma ��
<N
M
FID l. CRD
.+ N m
C
0
o a
s(
m
<
6
�
c
7 (Q N
cn
N N
3
w
N
w
fD C N
3
o 3
O
N 3
m
z
7 N
= o
(n N
m
O+ O
o3 3
to
m -o m
(On N
o p' j
7C
7 7
Z
3
C
6
N
N
�
n
� N
»
7
m'
n
n
N
n�
�
m'
Q
n
O 0
m
3 7
x
O c
7 3
N -O
7
w
(n O
n
O
7 7
O_
O p
O
7
m m
3
(p 7
N
N
m
O
mc
Ko
m
m
O
O_
<D
(n
N
3
� m
J
N
O
7
N
N -0
cQ
N3
fD
N O
O
A 7
m
7
N
7
C
(n
0
0
�
� n
3
c
m
c �-
D1
3 Q
(n �.
Q
o m
OQ
3-0
O
ent
O_
O
N
n
'0O N
= n
m
w m
7
fD
N o
(n
N -
w
N
N
O
r
o
7 N
3
O
3 O
�D
7
n
n O
7. N
0 Cf)
N N
7 7
O_ 0-
N
N Q
0
o p
o
N
w
=3
.� �.
j
J
7
(a Co
3
O _
1 Q
3 j
N �p
=3 m
7 7
p Co
C1
G Q
O
O
.3+
O
C N
O
N
cc-
Uel
T
I
irib Pap,
3
� 7
c
7
D
fOq
CODE
O
Reviewed By: Sean Hatch
Date: 05/11/16
o < O c
--i
3
m
s a c
° �D
o
N
O N O O 3 0 7
oma ��
N
�s
T
FID l. CRD
.+ N m
C
0
o a
s(
m
<
6
m ' m
c
N
c
cn
N N
3
nom+
N
fD C N
3
�
O
N 3
I<Df/J
y
7 N
n
D)
(n N
O+ O
6 c
(On N
N
N N
3
C
6
N
N
n
m
m'
n
n
N
m'
Q
m
x
x
w
n
O
O_
O
7
3
N
N
O
3
N
3
O
O_
N
N
O_
N
7
N
cQ
N
O
N
7
m
0
0
3
c
m
D1
Q
OQ
O
ent
O_
N
IANCE
m o M o
z 0 `°
O C C (D
C 0 m '. a �
C1 3 7 v O z n
m
c N v 0 m m
v - m
m n y O
a °. CD m
O r n
am N m 'a m O
O
3 r: W
y+ " N N n n
3 0' 6 4�-. m
a m y cQ
N m
N
7 N In
cn fD
m
0 z
3 O -4
Q a
- r
o'
7 m
o m
3
m m
a
m n
3 m
o n
m O
n �
m r
m D
z
n
m m
w m
l7 �
C
n O
a1
o O O v
z
7
2)
2 m
0 CD
3 Cn
c� D N
D_
N Q
Q �
Q• N
Cn
X C
71
W
N
O
O)
0
1
cc �
m
N �
O 77
o
CO 1
CD
v
0
z
3
O'
(D
7J 2
O m
O AVi
G) o
C <
Q
CD
Q ..
v
N
O
rn
0
W
W
0
N
w
w
Reviewed By: Sean Hatch
Date: 05/11/16
0
r CD
c �
7 N
0 m
CD
N �]
O CD
�. cn
CD
� Q
O
Al
� W
CD �.
N Q
D
Ln.
7 0
-0 al
.c•F t9
C
2
N O
a1 :3
CD
N
C
CD
D1
n 1
Q- o
Q• N
7 Cn
X C
71
K
a1
W
N
O
.,
0
1
Co
m
W M
O T
o
OD 1
0
D
D
0
N
X
n
T
w
a
o
QN
(Q
fD
Q
T
N
p
O
O
0
D
D
0.
o°o
w o
N
X
(Q
N
T
m
m
o
w
0
n
[�
°
O
(Qo
0 O
•*
0
C
wC
O
p
Z
n
W
C)
3
O_
T
0
O
ON
O
(
(
(
O0
Q
Q
Q
W
W
O
N
0
mW
N
fD
W
O
O
X
M
Q
w
j.
n
m
0
X
X
0
X
O
0
0
o
m
00 Ul
Ul Ul
00
OOi
X
X
Ol
h
h
7
h
h
o
o
V
n
0
0
0
9.
9'
fD
5'
S'
S'
S'
W �
m
z
z
w
w
O
y
O
O
fD
4
O
cQ
to
0
0
3
cQ
cQ
cQ
C
O
0
to
to
to
to
O
D
D
z
z
z
°
o
1
O
O
O
m
OD
N
O
N
N
N
N
Q Q
0
N
Q
Q
X
X
T
T
V
7
7
N a1
O
c
O
O
to
O
O
O
O
O
O
O
O
O
a
0
ax
o
0
0
O
N
3 .+
Reviewed By: Sean Hatch
Date: 05/11/16
0
r CD
c �
7 N
0 m
CD
N �]
O CD
�. cn
CD
� Q
O
Al
� W
CD �.
N Q
D
Ln.
7 0
-0 al
.c•F t9
C
2
N O
a1 :3
CD
N
C
CD
D1
n 1
Q- o
Q• N
7 Cn
X C
71
K
a1
W
N
O
.,
0
1
Co
m
W M
O T
o
OD 1
0
a
0
m
m
o
w
n
o
°
w
0
C
wC
M
0C
Z
7D
W
O0
O
W
W
W
N
0
mW
W
X
Q
j.
X
X
X
X
X
X
h
h
h
h
h
o
o
V
0
0
0
0
9.
9'
T
5'
S'
S'
S'
w
w
w
w
w
O
O
V
O
O
O
O
cQ
to
0
0
cQ
cQ
cQ
cQ
C
O
to
to
to
to
cc
D
D
T
0
D
D
D
D
1
1
N
N
N
N
N
N
Q Q
N
Q
Q
Q
Q
T
T
V
T
T
T
T
O
O
to
O
O
O
O
O
O
O
O
O
O
to
N
O
TI
�
O
�
O
3J
3J
3J
3J
o
o
�
�
�
�
0
7
p
O
O
O
O
Ui
Ul
Ul
Ul
O
O
O
O
O
CD
N
N
N
N
Nn+
W
D
1
—
—
—
—
0
-0
W
0
w
0
0
0
M
n
m
N
i�,
Ul
ul
C
CD
A
LNm
ul
UNi
UWi
Ui
UNi
UWi
3
7o
W
r
T
7o
W
r
T
7o
W
r
T
7
0
o
al
0
O
N
W
OD
W
mW
W
Ui
A
O
A
O
m
6)1
W
V
1
1
O
1
Ui
V
Ui
V
N
A
W
W
1
W
N
W
W
O
a
O
O
O
N
N
A
6)
N
W
m
V
V
W
N
N
N
O1
a a
A
W
1
O
W
W
NCD
$
O
O
Cm
OD
O
W
O
A
V
ro 0
"
o
0
0
0
0
0
0
0
0
0
0
0
0
0CD�
ao
m
x
m
x
m
x
m
x
m
x
z
z
z
z
z
z
z
m
x
m
x
m
x
m
x
m
x
m
x
m
x
N
j'
*
*
*
!'
g
j'
j'
j'
j'
j'
*
to
to
.1'PE
T
N
`c
to
`o
`o
`�
`�
Co
uidin
Dprt
et
0
CD
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
O
O
O
o
-
-
D
D
D
D
D
D
D
O
o
O
O
O
O
O
" 3 m
o
EVE
ED
FO
CO
E
O
PL
N
E
0 C4 a
Reviewed By: Sean Hatch
Date: 05/11/16
0
r CD
c �
7 N
0 m
CD
N �]
O CD
�. cn
CD
� Q
O
Al
� W
CD �.
N Q
D
Ln.
7 0
-0 al
.c•F t9
C
2
N O
a1 :3
CD
N
C
CD
D1
n 1
Q- o
Q• N
7 Cn
X C
71
K
a1
W
N
O
.,
0
1
Co
m
W M
O T
o
OD 1
CD
au
s'
z
3
O'
7J 2
O m
O AVi
T
+n O
N <
7 Q
D N
v ..
!D
Q
v
N
O
Ql
O
W
W
0
N
W
w
Reviewed By: Sean
Date: 05/11/16
v
0
0
O
z
O
00
O
N
�
�
v
N
T
7
7
N
O
(D
0—
W
O
N
�
CC
C
N
N
�
a
O_
O_
O_
O_
O_
O_
_�
O_
O_
z
:y
C
O
(D
O
A
V
O
O
O
0
Co
N
m
Cl)
Z
x
O
O
O
N
(D
C
O.
70
70
T
o
m
70
70
m
x
w
m
Z
(Q
(Q
(Q
O
Cul
o
98
uil
Jin
Q
MWD
1!09
CO I
Reviewed By: Sean
Date: 05/11/16
Hatch
0 m
r CD
c �
a,
0
0 m
N �]
CD
�. cn
CDQ
O
Al
� W
NQ -
A 5.
D
cncn
Fn'
7 0
-0 al
.,;
z
v
0
L
N
Q
O_
O_
O_
O_
O_
O_
_�
O_
O_
z
O
(D
(O
N
V
m
Ui
A
0
Co
N
O
O
N
C
70
70
T
o
70
70
70
m
w
m
(Q
(Q
(Q
m
m
o
W
CO
31
31
31
W
TO+
N
o
o
T
7
O
3
O
3
O
3
oo
O
7
N
N
A
1
1
1
N
Ui
Ui
N
C"
C
3
Q"
O
C
O
a
rQ
O
O
67
A
Co
Co
W
A
N
A
Co
0
N
c
N
N
N
m
m
m
m
m
Co
Co
('1
V
O
O
O
O
O
O
O
O
O
O
O
N
O
C"
C"
C"
Co
Co
Co
Co
Co
O
O
Co
0
>
m
>
m
>
m
>
m
>
m
>
m
E
m
>
m
>
m
>
m
m
O
O
O
O
O
O
O
O
O
O
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
-
(p
O
(D
7
7
7
7
7
7
7
7
7
7
3
Mo.
N
N
N
N
N
N
N
N
N
N
N
C
N
C
N
C
N
C
N
C
N
C
N
C
N
C
N
C
N
C
O
U2
Z
Z
Z
X
X
X
X
X
X
X
N
J
0
O
O
O
O
O
O
O
om<
n
,x(�
zD
z
z
z
z
z
z
O
O
O
O
O
O
O
—
3 C4 Q-
C
MIILIPNCE
Hatch
0 m
r CD
c �
a,
0
0 m
N �]
CD
�. cn
CDQ
O
Al
� W
NQ -
A 5.
D
cncn
Fn'
7 0
-0 al
.,;
CD
0
7
z
3
0-
7J 2
O m
O AVi
G) 3
CD <
Q
vCD
Q
N
0
N
Ol
O
W
W
0
N
W
w
Reviewed By: Sean Hatch
Date: 05/11/16
n
� O
r CD
C �
is �*
0
v m
N �]
O (p
�. cn
N
O
7
Al
� W
N Q
D
L
cn
C n
� O
z 7
al
N �
C
A -F1
CD
3 N
D
CL 1
Q- o
Q• N
7 Cn
X C
71
K
a1
W
N
O
y
0
D
D
a
C
?o
ca
0
-n
0
O
�o
oT
0
o
m
N
U7
00
x
xf
�
N-'
x
OC
x
°
m
o
O
o
a
0
�"�
7"I
<
O
/''�
\ /
O
r
o
D
to
0
O
_D
°i
3
m
n
O
N
O
CD
1l
O
O
iii
(O
N
j
�
m
a
n
S
m
x
C)
D
m
C7
D
D
x
c
1
Z
m
°
wto
u
m
o'
0
�_ in
m
°
w�
(n
0
�_ in
5
�'
w�
Lt. W
o'
w
0
O
N
.
� �
<n
Q
n <
3J
O
O
.
� M
n <
3J
O
O
3J
O
O
�
<D
N
57
0
CD
57
CD
0
`G
O
O
O
O
0
O
O
O
O
O
O_
O
O
O
O
O_
O
O
O
O
3
N
O'
-n
'
T
-n
-n
T
-n
-n
O'
3
3
3
3
3
3
3
3
3
C1
r.
O
w
N
Q
N
O
Q
N
O-
O
Q
Q
Q
N
C
O
O
O
O
O
O
X
X
X
0
0
0
a
a
C)
a
C)
N
N
O
O
A
P,
N
O
O
a
nn
@
�'1�'1
nrnF
T31
N
-P,Cm
O
N
-P,
O
O
NJ
'
am
Op
O
5'
n
oo-P'no
O
n
O
5F
c4
O
O
O
O
O
O
p
O
O
N
N
N
N
N
N
A
A
A
O
C4
>
>
>
>
>
>
>
w n
al
u,
00
v,
(0
m
m
m
m
m
m
m
c
m _
7
O
O
O
O
O
O
O
O
O
d)
O
N
O
O
O
N
O
d)d)
O
O
A
O
W
y
00
d)
N
U7
00
(0
A
(0
A
A
J
J
00
1
d)
A
A
A
A
00
O
N
O
C (p
fD N
C4
7
. . .
oCp�3-
. . .
ops
. . .
cnmp �3-
W
. . .
p„„
goo
. . . . . .
ps
oo� ?�`�
. . .
ops
��W
. . .
p„„
goo
. . .
oo�
. . .
oo<
. .
�3-
<C
. . .
cnmp �3-
kQL)Co
v„
ov„v„
von
��vv„
ov„
von
lpmv
v„v„
vID ID�v�
v ��
.v v�
v�
v C)
v
v
vR
v�vCO
CO
:A (pcn
�O cn
0 0
G
�� G
O O
p O
Oa
G
Q�Oa
n 0 3'G
6
O
\3
a k�
rv"3
Crvoo
��\3
k�
\ate
Dain 3
ar= a =oo
��3
COrvoo
a�
=tea
Dain
a
Dain
a� =
C) 3
=oo
tau, 3
=oo
r
,p0
k O
,p0
,^��
�\
3 y \ 0
3y \
\
Z3-zr
\O
\O
y
00
C)
m
O
Q
k
m. k
z m k
k Q
k Q
v
C
?
3
/�� ttitt
V V
'
�-
Or Q
3 Z^. 0
•1�
•1�
y
a
0
Building
DLia
4l
a
\
`tea
?
�a
�
4VI WED F
R CO D
E C6M RLIANCE
Reviewed By: Sean Hatch
Date: 05/11/16
n
� O
r CD
C �
is �*
0
v m
N �]
O (p
�. cn
N
O
7
Al
� W
N Q
D
L
cn
C n
� O
z 7
al
N �
C
A -F1
CD
3 N
D
CL 1
Q- o
Q• N
7 Cn
X C
71
K
a1
W
N
O
y
/
/
2
/
7
Reviewed B :Sean Hatch
Dat: 05/1£18
t
ƒ
0
>
n
m
/
0
°
o
ƒ
k
3
a
k
0
®
®
k{\
\
C')
8
2
(n
f
®
\\
2
8
0
k
v
0
2
\
\,3
k
S
z
�
�
2
?
�
o
*
7
/
/
ƒ
�
}
&
\
(D<
r
CL
I�
0
-7{
\\{
n
�0
$g
CD §
>
-n
to
2
E
�
T
v
/
§ \
/
[
CL
»
v
ƒo2#
}\g7
S
-�0
0
(m 8Co
-�
�-n
E
}�
/
R
M0
o
C§
x
ƒ
o
/
[OD
7
\
u|
ED
FO
RIE
Reviewed B :Sean Hatch
Dat: 05/1£18
\ CD
0
0 /
k ƒ
i
\ /
\ /
N) &
\ aD
�
£
e
-0 2
� @
\ \
ƒ :3
/ Q
ƒ
�
/ e
> �
\ \
\ /
E 9
�
a
/
CDN)
n
M
% M
a o
CO "
t
m
I
$
)
o
ƒ
\
9
I
f
/
\
8
k
v
2
\
{
}
S
z
�
2
?
(
*
7
/
ƒ
�
}
&
I�
-7{
S
�0
>
-n
4
\
7k°
�7#
E
T
ƒ
o
w
/
[
ƒ
o)
0
(m 8Co
m
2
\ CD
0
0 /
k ƒ
i
\ /
\ /
N) &
\ aD
�
£
e
-0 2
� @
\ \
ƒ :3
/ Q
ƒ
�
/ e
> �
\ \
\ /
E 9
�
a
/
CDN)
n
M
% M
a o
CO "
CD
v
0
z
3
Cy -
7J x
CD m
O AVi
G) o
CD <
7 Q
D N
v ..
!D
Q
v
N
O
N
rn
0
w
w
N
0
N
w
w
Bui
REVIEWED FOf
Reviewed By: Sean Hatch
Date: 05/11/16
c �
.•. c
� O
Z 7
al
N �
N
C
CDC
D1
CL 1
Q- o
Q• N
=$ Cn
X C
P
K
allW
N
O
y
x
a
D
n
0
o
n
(n 0
w
o
3
O
6
(D
O
r
o.
W
m
C
3
--I
O
Z
0
N
`n
a
m
o
N
G
O
N
�
�
N
n
w
N
n'
N
m
v
C
N
<n x
m
3 w.
o. =3
n
o
w
m' -
w
3
w
5'
N
m
m
O
p
� C
a1 a1
A
C
<D O
n
N
N
r c
W
_D
0
a <
0
m
o' v
cn
N
O
7
r�
0 c
D
0
o' v
0
con
W
0
Z
m
j
Co
O
�
v
c
n
Z
m
x
a)o
(n
N
=3O+
ID
O 0-
Co
+
C
N
Z
m
N
z
m
o
n
O
Z
o
3 Q
O
(o
K
O
7 N
7
ntz
x
� m
o
D
a. N
O
CE
'
c �
.•. c
� O
Z 7
al
N �
N
C
CDC
D1
CL 1
Q- o
Q• N
=$ Cn
X C
P
K
allW
N
O
y
x
a
0
n
0
o
n
to
O
0
O
r
�
m
-<
N
3
--I
m
9
N
a
D
0
0
N
N
N a
N
3 w.
n
o
�
n
o'
5'
1
m
m
O
w
n
N
W
m
A
m
N
O
7
0
0
con
0
m
a
n
O C
Z
O N
a)o
6
N ID
N
ID
O 0-
m m
m
N
z
m
o
O
c �
.•. c
� O
Z 7
al
N �
N
C
CDC
D1
CL 1
Q- o
Q• N
=$ Cn
X C
P
K
allW
N
O
y
0
>
CL
0
0
m
CD
—
W rl) 0
CD
m
m
0
>
CL
0
0
0
0
0
CO
CL
9
0)
-0
0
CO
m
CL
0
CD
0
0 0)
0
Z
CD
;7�
N2:
CD
0 CD
- CD CC(D CD 9
107
(j)
Fa
,
Z
-1
0
CD•2+ a
m
M
fn N(D (D
C
o CL F, C: C:
CD CD =3
CD
a
C
z
5D
CD CD (DCL
0
3Z
0-0
0 (D (o ;�. 0
3
RL
CD
0
M
:3 W '<
Cn
rn
gm 20, 01
0
r-,
f
557 CD CZ
0 CnN
f11
M, CD
0
-0 C:
CD CD
M
CL
0
o
0 L
IDr_
C=D' CCDI
0 0
o
Z
90 i
3
(a CO
CD
(n PO CD Cl ID
z
m
j
m
CD 0
Z
Cn
W =r
0
CD CD ID (D
CL = Co
y
0
si
=. 0
CL Co &
RL
O.
CD 0 a 2L 0
1 :3 (=D CD —
= 5 = 0
6
CL
0
us. = E
CD W
0
3
0 C) CL 0
0 0 0
1
3 CD ni
a
CD
(D
0 m
(CCD -0 CD 0
0
0
,<
0 n CS
03
W CD '<
a AiQ, 0-
-0
0
0
=r
0
CD
a)
(D
CO)
-a
0
CD 0 =r
CD
0
m CQ
>
0
0
=3
0
=
3
a
CD
C:
Ei
CO
Co
(D
CD
t
(D
=r 0
— =
CD (0
CD
0
mCL
0
=r Cn
0 CL
Cl ID
(D CD
0
Cn.
0- 0
=r
CL
0 CD
Z5'
CD=r =:K
CD
0-
CD
3 5'
M
CL
CD
0
a C)
\1
CD
0
3
(D
CD
<
0
0
�7
7
(D
CL (D 0
fa„sz�
0
= ;4: o
0
=r -0
0
0 a.
W
-0
g
(D
00 rn
3
a
=r
CD
0
CUF'EkTF�O
0
Ek
B
ildin,
0
) ErbPattmed
21
J2ZP-F�N/!ALFl)
EID
P CO
aLLL=PLL&W
CE
Reviewed By: Sean Hatch
Date: 05/11/16
0 "a 0
0 " m
M
0 z -n
0 0
C; (D m
0
0 (D -n
o
0
(D
ro O o
th, m
>
m
m
Yj- a
0
n
(D -0
CD M
o
RESIDENTIAL MEASURES SUMMARY
RMS-1
Project Name
Sathe Addition
Building Type 0 Single Family ❑ Addition Alone
❑ Multi Family 12 Existing+ Addition/Alteration
Date
3/13/2016
Project Address
1103 Kentwood Ave Cupertino
California Energy Climate Zone
CA Climate Zone 04
Total Cond. Floor Area
2,041
Addition
464
# of Units
1
INSULATION
Construction Type
Area
Cavity vo Special Features Status
Floor Wood Framed w/Crawl Space - no insulation 1,577 Existing
Wall Wood Framed - no insulation 833 Existing
Roof Wood Framed Attic R11 1,577 Existing
Floor Wood Framed w/Crawl Space R 19 464 New
Wall Wood Framed R 15 604 New
Door Opaque Door - no insulation 20 New
Roof Wood Framed Attic R38 464 New
Demising Wood Framed - no insulation 328 New
FENESTRATION I Total Area: 229 Glazing Percentage: 11-2%1New/Altered Average U-Factor: 0.32
Orientation Area(ft) U-Fac SHGC Overhang Sidefins Exterior Shades Status
Front (NE) 24.0 1.280
0.80 none none Bug Screen Existing
Left (SE) 36.0 1.280
0.80 none none Bug Screen Existing
Rear (SW) 53.3 1.280
0.80 none none Bug Screen Existing
Right (Nw) 60.0 1.280
0.80 none none Bug Screen Existing
Front (NE) 16.0 0.320
0.25 none none Bug Screen New
Rear (SW) 40.0 0.320
0.25 none none Bug Screen New
HVAC SYSTEMS
Ot . Heating Min. Eff
Cooling Min. Eff Thermostat Status
1 Central Furnace 78% AFUE
Split Air Conditioner 13.0 SEER Setback
Existing
HVAC DISTRIBUTION
Location Heating
Duct
Cooling Duct Location R-Value Status
HVAC System Ducted
Ducted Attic 6.0 Altered
WATER HEATING
Ot . Type Gallons Min. Eff Distribution Status
CUPERTINO
a—
to
9LA1di mj-BeVaft
Ener Pro 6.7 by Ener Soft User Number: 6249
RunCode: 2016-03-13T11:03:11 ID: 16-03134
Pa e 11 of 16
nFvir-vvw run %..uur- 4VIvirLI1AIVI,C
Reviewed By: Sean Hatch
Date: 05/11/16
2013 Low -Rise Residential Mandatory Measures Summary
NOTE: Low-rise residential buildings subject to the Standards must comply with all applicable mandatory measures listed, regardless of the
compliance approach used. Exceptions may apply. Review the respective code section for more information.
Building Envelope Measures:
§ 110.6(a)l :
Doors and windows between conditioned and unconditioned spaces are manufactured to limit air leakage.
§110.6(a)5:
Fenestration products (except field -fabricated windows) have a label listing the certified U -Factor, certified Solar Heat Gain
Coefficient SHGC , and infiltration that meets the requirements of §10-111 (a).
§ 110.7:
Exterior doors and windows are weatherstripped; all joints and penetrations are caulked and sealed.
§110.8(a):
Insulation specified or installed meets Standards for Insulating Material. Indicate type and include on the CF2R.
§ 110.8(i):
The thermal emittance and aged solar reflectance values of the cool roofing material meets the requirements of § 110.8(i) when the
installation of a cool roof is specified on the CF I R.
§ 110.80):
A radiant barrier shall have an emittance of 0.05 or less when the installation of a radiant barrier is specified on the CF 1 R.
Minimum R-30 insulation in wood -frame ceiling; or the weighted average U -factor shall not exceed 0.031. Minimum R-19 in a
§150.0(a):
rafter roof alteration. Attic access doors shall have permanently attached insulation using adhesive or mechanical fasteners. The
attic access shall be gasketed to prevent air leakage.
§150.0(b):
Loose fill insulation shall conform with manufacturer's installed design labeled R -value.
§150.0(c):
Minimum R-13 insulation in 2x4 inch wood framing wall or have a U -factor of 0.102 or less (R-19 in 2x6 or 0.074 maximum U -
factor).
§150.0(d):
Minimum R-19 insulation in raised wood -frame floor or 0.037 maximum U -factor.
In Climate Zones 14 and 16 a Class II vapor retarder shall be installed on the conditioned space side of all insulation in all exterior
§150.0(g)l:
walls, vented attics and unvented attics with air -permeable insulation.
In Climate Zones 1-16 with unvented crawl spaces the earth floor of the crawl space shall be covered with a Class I or Class II
§150.0(g)2:
vapor retarder.
In a building having a controlled ventilation crawl space, a Class I or Class II vapor retarder shall be placed over the earth floor of
§150.0(g)3:
the crawl space to reduce moisture entry and protect insulation from condensation, as specified in the exception to Section
150.0(d).
§150.0(1):
Slab edge insulation shall: have a water absorption rate, for the insulation material alone without facings, no greater than 0.3%;
have water vapor permeance rate is no greater than 2.0 perm/inch, be protected from physical damage and UV light deterioration;
and when installed as part of a heated slab floor meets the requirements of § 110.8(g).
150.0
§ (�'
Fenestration, including skylights, separating conditioned space from unconditioned space or outdoors shall have a maximum U-
factor of 0.58; or the weighted average U -factor of all fenestration shall not exceed 0.58.
Fireplaces, Decorative Gas Appliances and Gas Log Measures:
§150.0(e)IA:
Masonry or factory -built fireplaces have a closable metal or glass door covering the entire opening of the firebox.
§150.0(e)1B:
Masonry or factory -built fireplaces have a combustion outside air intake, which is at least six square inches in area and is
equipped with a readily accessible, operable, and tigbt-fitting damper or a combustion -air control device.
§150.0(e)1C:
Masonry or factory -built fireplaces have a flue damper with a readily accessible control.
§150.0(e)2:
Continuous burning pilot lights and the use of indoor air for cooling a firebox jacket, when that indoor air is vented to the outside
of the building, are prohibited.
Space Conditioning, Water Heating and Plumbing System Measures:
§ 110.0-§ 110.3:
HVAC equipment, water heaters, showerheads, faucets and all other regulated appliances are certified to the Energy Commission.
§ 110.3(c)5:
water heating recirculation loops serving multiple dwelling units meet the air release valve, backflow prevention, pump isolation
valve, and recirculation loop connection requirements of §110.3(c)5.
Continuously burning pilot lights are prohibited for natural gas: fan -type central furnaces, household cooking appliances (appli-
§110.5:
ances without an electrical supply voltage connection with pilot lights that consume less than 150 Btu/hr are exempt), and pool
ands a heaters.
§150.0(h)l:
Heating and/or cooling loads are calculated in accordance with ASHRAE, SMACNA or ACCA using design conditions specified
in §150.0(h)2.
§ 150.0(h)3A:
Installed air conditioner and heat pump outdoor condensing units shall have a clearance of at least five feet from the outlet of any
dryer vent.
§150.0(i):
Heating systems are equipped with thermostats that meet the setback requirements of § 110.2(c).
§150.00)1A:
Storage gas water heaters with an energy factor equal to or less than the federal minimum standards shall be externally wrapped
with insulation having an installed thermal resistance of R-12 or greater.
§150.00)1B:
Unfired hot water tanks, such as storage tanks and backup storage tanks for solar water -heating systems, have R-12 external
insulation or R-16 internal insulation where the internal insulation R -value is indicated on the exterior of the tank.
For domestic hot water system pi
.
er buried or unburied: the first 5 feet of hot and cold water pipes from the storage
tank, all piping with a nominal di
4 indUPE9lin associated with a domestic hot water recirculation system
§150.00)2A:
regardless of the pipe diameter, pi
g
he hea ing source to s orage tank or between tanks, piping buried below grade, and
all hot water pipes from the heatin
kEWiff19LgrDep1t11#tl t1tted according to the requirements of TABLE 120.3-
A.
§150.00)2B:
All domestic hot water pipes that are buried
that allows for installation, removB,EaYTWOAQ
below grade must be instal led in a water proof and non -crushable casing or sleeve
gPR�,gqP Pd�*N�rd insulation.
Reviewed By: Sean Hatch
Date: 05/11/16
2013 Low -Rise Residential Mandatory Measures Summary
§150.00)2C:
Pipe for cooling system lines shall be insulated as specified in § 150.00)2A. Piping insulation for steam and hydronic heating
systems or hot water systems with pressure> 15 psig shall meet the requirements in TABLE 120.3-A.
§150.00)3:
Insulation is protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind.
Insulation exposed to weather shall either be rated for outdoor use or installed with a cover suitable for outdoor service. For
§150.00)3A:
example, protected by aluminum, sheet metal, painted canvas, or plastic cover. Cellular foam insulation protected as specified or
painted with coating that is water retardant and provides shielding from solar radiation that degrades the material.
Insulation covering chilled water piping and refrigerant suction piping located outside the conditioned space shall have a Class I
§150.00)3B:
or Class II vapor retarding facing, or the insulation shall be installed at the thickness that qualifies as a Class I or Class 11 vapor
retarder.
Systems using gas or propane water heaters to serve individual dwelling units shall include: a 120V electrical receptacle within 3
feet of the water heater; a Category III or IV vent, or a Type B vent with straight pipe between the outside termination and the
§150.0(n)l:
space where the water heater is installed; a condensate drain that is no more than 2 inches higher than the base of the installed
water heater, and allows natural draining without pump assistance; and a gas supply line with a capacity of at least 200,000
Btu/hr.
§150.0(n)2:
Recirculating loops serving multiple dwelling units shall meet the requirements of §110.3(c)5.
§150.0(n)3:
Solar water -heating systems and collectors shall be certified and rated by the Solar Rating and Certification Corporation (SRCC)
or by a testing agency approved by the Executive Director.
Ducts and Fans Measures:
All air -distribution system ducts and plenums installed are sealed and insulated to meet the requirements of CMC §601.0, §602.0,
§603.0, §604.0, §605.0 and ANSI/SMACNA-006-2006 HVAC Duct Construction Standards Metal and Flexible 3rd Edition.
Supply -air and return -air ducts and plenums are insulated to a minimum installed level of R-6.0 (or higher if required by CMC
§605.0) or enclosed entirely in directly conditioned space as confirmed through field verification and diagnostic testing
(RA3.1.4.3.8). Connections of metal ducts and inner core of flexible ducts are mechanically fastened. Openings shall be sealed
§150.0(m)l:
with mastic, tape, or other duct -closure system that meets the applicable requirements of UL 181, UL 181A, or UL 181B or
aerosol sealant that meets the requirements of UL 723. If mastic or tape is used to seal openings greater than 1/4 inch, the
combination of mastic and either mesh or tape shall be used. Building cavities, support platforms for air handlers, and plenums
defined or constructed with materials other than sealed sheet metal, duct board or flexible duct shall not be used for conveying
conditioned air. Building cavities and support platforms may contain ducts. Ducts installed in cavities and support platforms
shall not be compressed to cause reductions in the cross-sectional area of the ducts.
Factory -Fabricated Duct Systems shall comply with specified requirements for duct construction, connections, and closures; joints
§150.0(m)2:
and seams of duct systems and their components shall not be sealed with cloth back rubber adhesive duct tapes unless such tape is
used in combination with mastic and draw bands.
§150.0(m)3-6:
Field -Fabricated Duct Systems shall comply with requirements for: pressure -sensitive tapes, mastics, sealants, and other
requirements specified for duct construction; duct insulation R -value ratings; duct insulation thickness; and duct labeling.
§150.0(m)7:
All fan systems that exchange air between the conditioned space and the outside of the building must have backdraft or automatic
dampers.
§150.0(M)8:
Gravity ventilating systems serving conditioned space have either automatic or readily accessible, manually operated dampers
except combustion inlet and outlet air openings and elevator shaft vents.
Insulation shall be protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind but not
§150.0(m)9:
limited to the following: insulation exposed to weather shall be suitable for outdoor service. For example, protected by aluminum,
sheet metal, painted canvas, or plastic cover. Cellular foam insulation shall be protected as above or painted with a coating that is
water retardant and provides shielding from solar radiation.
§150.0(m)10:
Flexible ducts cannot have porous inner cores.
When space conditioning systems use forced air duct systems to supply conditioned air to an occupiable space, the ducts shall be
§150.0(m)l1:
sealed and duct leakage tested, as confirmed through field verification and diagnostic testing, in accordance with Reference
Residential Appendix RA3.
Mechanical systems that supply air to an occupiable space through ductwork exceeding 10 feet in length and through a thermal
§150.0(m)12:
conditioning component, except evaporative coolers, shall be provided with air filter devices that meet the requirements of
§150.0(m)12.
Space conditioning systems that utilize forced air ducts to supply cooling to an occupiable space shall have a hole for the
placement of a static pressure probe (HSPP), or a permanently installed static pressure probe (PSPP) in the supply plenum. The
§150.0(m)13:
space conditioning system must also demonstrate airflow> 350 CFM per ton of nominal cooling capacity through the return
grilles, and an air -handling unit fan efficacy < 0.58 W/CFM as confirmed by field verification and diagnostic testing, in
accordance with Reference Residential Appendix RA3.
Zonally controlled central forced air cooling systems shall be capable of simultaneously delivering, in every zonal control mode,
§150.0(m)15:
an airflow from the dwelling, through the air handler fan and delivered to the dwelling, of> 350 CFM per ton of nominal cooling
capacity, and operating at an air -handling unit fan efficacy of < 0.58 W/CFM as confirmed by field verification and diagnostic
testing, in accordance with Reference Residential Appendix RA3.
All dwelling units shall meet the requirements of ASHRAE Standard 62.2. Neither window operation nor continuous operation of
§150.0(0):
central forced air system air handlers used in central fan integrated ventilation systems are permissible methods of providing the
Whole Building Ventilation.
§150.0(o)lA:
Whole Building Ventilation airflo
on fir%*1WKrrWFTJ1Wification and diagnostic testing, in accordance with
Reference Residential Appendix F,BLL&LLl3}Departmonf
Pool and Spa Heating Systems and Equipment M
Any pool or spa heating system shkl n d Ftl }�q�,l f Iq pct that complies with the Appliance Efficiency
§ 110.4(a):
Regulations; an on switch moun ed outsi e of the eater that aows shut mg off the heater without adjusting the thermostat
setting; a permanent weatherproofRputewedrswiSep tHgitchuctions; and shall not use electric resistance heating.
Date: 05/11/16
2013 Low -Rise Residential Mandatory Measures Summary
§ 110.4(b)1:
Any pool or spa heating equipment shall be installed with at least 36 inches of pipe between filter and heater or dedicated suction
and return lines, or built-up connections for future solar heating.
§ 110.4(b)2:
Outdoor pools or spas that have a heat pump or gas heater shall have a cover.
§ 110.4(b)3:
Pools shall have directional inlets that adequately mix the pool water, and a time switch that will allow all pumps to be set or pro-
grammed to run only during off-peak electric demand periods.
§ 110.5:
Natural gas pool and spa heaters shall not have a continuous burning pilot light.
§150.0(p):
Residential pool systems or equipment shall meet specified pump sizing, flow rate, piping, filters, and valve requirements.
Lighting Measures:
§ 110.9:
All lighting control devices and systems, ballasts, and luminaires shall meet the applicable requirements of § 110.9.
§ 150.0(k)IA:
Installed luminaires shall be classified as high -efficacy or low -efficacy for compliance with § 150.0(k) in accordance with TABLE
150.0-A or TABLE 150.0-B, as applicable.
§150.0(k)1B:
When a high efficacy and low efficacy lighting system are combined in a single luminaire, each system shall separately comply
with the applicable provisions of §150.0(k).
The wattage and classification of permanently installed luminaires in residential kitchens shall be determined in accordance with
§150.0(k)1C:
§ I30.0(c). In residential kitchens, the wattage of electrical boxes finished with a blank cover or where no electrical equipment has
been installed, and where the electrical box can be used for a luminaire or a surface mounted ceiling fan, shall be calculated as 180
watts of low efficacy lighting per electrical box.
§ 150.0(k)1D:
Ballasts for fluorescent lamps rated 13 watts or greater shall be electronic and shall have an output frequency no less than 20 kHz.
Permanently installed night lights and night lights integral to installed luminaires or exhaust fans shall be rated to consume no
§150.0(k)IE:
more than 5 watts of power per luminaire or exhaust fan as determined in accordance with § I30.0(c). Night lights do not need to
be controlled by vacancy sensors.
§ 150.0(k)1F:
Lighting integral to exhaust fans (except when installed by the manufacturer in kitchen exhaust hoods) shall meet the applicable
requirements of §150.0(k).
§ 150.0(k)2A:
High efficacy luminaires must be switched separately from low efficacy luminaires.
§150.0(k)2B:
Exhaust fans shall be switched separately from lighting systems.
§ 150.0(k)2C:
Luminaires shall be switched with readily accessible controls that permit the luminaires to be manually switched ON and OFF.
§150.0(k)2D:
Controls and equipment are installed in accordance with manufacturer's instructions.
§ 150.0(k)2E:
No control shall bypass a dimmer or vacancy sensor function if the control is installed to comply with § 150.0(k).
§150.0(k)2F:
Lighting controls comply with applicable requirements of §110.9.
An Energy Management Control System (EMCS) may be used to comply with dimmer requirements if: it functions as a dimmer
§150.0(k)2G:
according to §110.9; meets Installation Certificate requirements of §130.4; the EMCS requirements of §130.5; and all other
requirements in §150.0(k)2.
An Energy Management Control System (EMCS) may be used to comply with vacancy sensor requirements of § I50.0(k) if: it
§150.0(k)2H:
functions as a vacancy sensor according to §110.9; meets Installation Certificate requirements of §130.4; the EMCS requirements
of § 130.5; and all other requirements in § 150.0(k)2.
§150.0(k)21:
A multiscene programmable controller may be used to comply with dimmer requirements of this section if it provides the
functionality of a dimmer according to §110.9, and complies with all other applicable requirements in §I50.0(k)2.
§150.0(k)3A:
A minimum of 50 percent of the total rated wattage of permanently installed lighting in kitchens shall be high efficacy.
Kitchen lighting includes all permanently installed lighting in the kitchen except internal lighting in cabinets that illuminate only
§ 150.0(k)3B:
the inside of the cabinets. Lighting in areas adjacent to the kitchen, including but not limited to dining and nook areas, are
considered kitchen lighting if they are not separately switched from kitchen lighting.
§150.0(k)4:
Permanently installed lighting that is internal to cabinets shall use no more than 20 watts of power per linear foot of illuminated
cabinet.
§150.0(k)5:
A minimum of one high efficacy luminaire shall be installed in each bathroom; and all other lighting installed in each bathroom
shall be high efficacy or controlled by vacancy sensors.
§150.0(k)6:
Lighting installed in attached and detached garages, laundry rooms, and utility rooms shall be high efficacy luminaires and
controlled by vacancy sensors.
§150.0(k)7:
Lighting installed in rooms or areas other than in kitchens, bathrooms, garages, laundry rooms, and utility rooms shall be high
efficacy, or shall be controlled by either dimmers or vacancy sensors.
Luminaires recessed into ceilings shall: be listed for zero clearance insulation contact (IC) by Underwriters Laboratories or other
nationally recognized testing/rating laboratory; have a label that certifies that the luminaire is airtight with air leakage less than 2.0
CFM at 75 Pascals when tested in accordance with ASTM E283; be sealed with a gasket or caulk between the luminaire housing
§150.0(k)8:
and ceiling, and shall have all air leak paths between conditioned and unconditioned spaces sealed with a gasket or caulk; and
allow ballast maintenance and replacement without requiring cutting holes in the ceiling.
For recessed compact fluorescent luminaries with ballasts to qualify as high efficacy for compliance with § 150.0(k), the ballasts
shall be certified to the Energy Commission to comply with the applicable requirements in § 110.9.
For single-family residential build or lightin permanently mounted to a residential building or other buildings on the
UPERlTIROhe
same lot shall be high efficacy, or effi� following requirements:
i. Controlled by a manual ON and R' h U t err Att.�, Ntthe automatic actions of Items ii or iii below; and
§ 150.0(k)9A:
ii. Controlled by a motion sensor n override of l�yp�ss swii'c Tat disables the motion sensor, or controlled by a
motion sensor having a temporary itch which temporarily bypasses the motion sensing function and automatically
reactivates the motion sensor widik'E IRWE WOR CODE COMPLIANCE
iii. Controlled by one of the following methods:
Reviewed ny: Jeai i rldLU i
Date: 05/11/16
2013 Low -Rise Residential Mandatory Measures Summary
1,0urr-K i iNv
Building Department
REVIEWED FOR CODE COMPLIANCE
Reviewed By: Sean Hatch
Date: 05/11/16
a. Photocontrol not having an override or bypass switch that disables the photocontrol; or
b. Astronomical time clock not having an override or bypass switch that disables the astronomical time clock, and which is
programmed to automatically turn the outdoor lighting OFF during daylight hours; or
c. Energy management control system which meets all of the following requirements: At a minimum provides the functionality of
an astronomical time clock in accordance with §110.9; meets the Installation Certification requirements in §130.4; meets the
requirements for an EMCS in § 130.5; does not have an override or bypass switch that allows the luminaire to be always ON; and,
is programmed to automatically turn the outdoor lighting OFF during daylight hours.
For low-rise multifamily residential buildings, outdoor lighting for private patios, entrances, balconies, and porches; and outdoor
lighting for residential parking lots and residential carports with less than eight vehicles per site shall comply with one of the
§150.0(k)9B:
following requirements:
i. Shall comply with §150.0(k)9A; or
ii. Shall comply with the applicable requirements in §110.9, §130.0, §130.2, §130.4, §140.7 and §141.0.
§ 150.0(k)9C:
For low-rise residential buildings with four or more dwelling units, outdoor lighting not regulated by § 150.0(k)9B or 150.0(k)9D
shall comply with the applicable requirements in §110.9, §130.0, §130.2, §130.4, §140.7 and §141.0.
§ 150.0(k)9D:
Outdoor lighting for residential parking lots and residential carports with a total of eight or more vehicles per site shall comply
with the applicable requirements in §110.9, §130.0, §130.2, §130.4, §140.7 and §141.0.
§150.0(k)10:
Internally illuminated address signs shall comply with §140.8; or shall consume no more than 5 watts of power as determined
according to §130.0(c).
§150.0(k)l1:
Lighting for residential parking garages for eight or more vehicles shall comply with the applicable requirements for
nonresidential garages in §110.9, §130.0, §130.1, §130.4, §140.6, and §141.0.
In a low-rise multifamily residential building where the total interior common area in a single building equals 20 percent or less of
§ 150.0(k)12A:
the floor area, permanently installed lighting for the interior common areas in that building shall be high efficacy luminaires or
controlled by an occupant sensor.
In a low-rise multifamily residential building where the total interior common area in a single building equals more than 20
percent of the floor area, permanently installed lighting in that building shall:
§150.0(k)12B:
i. Comply with the applicable requirements in §110.9, §130.0, §130.1, §140.6 and §141.0; and
ii. Lighting installed in corridors and stairwells shall be controlled by occupant sensors that reduce the lighting power in each
space by at least 50 percent. The occupant sensors shall be capable of turning the light fully On and Off from all designed paths of
ingress and egress.
Solar Ready Buildings:
Single family residences located in subdivisions with ten or more single family residences and where the application for a
§110.10(a)l:
tentative subdivision map for the residences has been deemed complete, by the enforcement agency, on or after January 1, 2014,
shall comply with the requirements of §110.10(b) through §110.10(e).
§110.10(a)2:
Low-rise multi -family buildings shall comply with the requirements of §110.10(b) through §110.10(d).
The solar zone shall have a minimum total area as described below. The solar zone shall comply with access, pathway, smoke
ventilation, and spacing requirements as specified in Title 24, Part 9 or other Parts of Title 24 or in any requirements adopted by a
local jurisdiction. The solar zone total area shall be comprised of areas that have no dimension less than 5 feet and are no less than
80 square feet each for buildings with roof areas less than or equal to 10,000 square feet or no less than 160 square feet each for
§110.10(b)1:
buildings with roof areas greater than 10,000 square feet.
For single family residences the solar zone shall be located on the roof or overhang of the building and have a total area no less
than 250 square feet. For low-rise multi -family buildings the solar zone shall be located on the roof or overhang of the building or
on the roof or overhang of another structure located within 250 feet of the building or on covered parking installed with the
building project and have a total area no less than 15 percent of the total roof area of the building excluding any skylight area.
§ 110.10(b)2:
All sections of the solar zone located on steep -sloped roofs shall be oriented between 110 degrees and 270 degrees of true north.
§ 110.10(b)3A:
No obstructions, including but not limited to, vents, chimneys, architectural features, and roof mounted equipment, shall be
located in the solar zone.
Any obstruction, located on the roof or any other part of the building that projects above a solar zone shall be located at least twice
§ 110.10(b)3B:
the distance, measured in the horizontal plane, of the height difference between the highest point of the obstruction and the
horizontal projection of the nearest point of the solar zone, measured in the vertical plane.
§ 110.10(b)4:
For areas of the roof designated as solar zone, the structural design loads for roof dead load and roof live load shall be clearly
indicated on the construction documents.
The construction documents shall indicate: a location for inverters and metering equipment and a pathway for routing of conduit
§ 110.10(c):
from the solar zone to the point of interconnection with the electrical service (for single family residences the point of
interconnection will be the main service panel); a pathway for routing of plumbing from the solar zone to the water -heating
system.
§110.10(d):
A copy of the construction documents or a comparable document indicating the information from §110.10(b) through §110.10(c)
shall be provided to the occupant.
§ 110.10(e)l :
The main electrical service panel shall have a minimum busbar rating of 200 amps.
The main electrical service panel shall have a reserved space to allow for the installation of a double pole circuit breaker for a
§110.10(e)2:
future solar electric installation. The reserved space shall be: positioned at the opposite (load) end from the input feeder location or
main circuit location, and perman _ d as "For Future Solar Electric".
1,0urr-K i iNv
Building Department
REVIEWED FOR CODE COMPLIANCE
Reviewed By: Sean Hatch
Date: 05/11/16
ROOM LOAD SUMMARY
Project Name Date
Sathe Addition 3/13/2016
System Name Floor Area
HVAC System 2,041
ROOM LOAD SUMMARY
ROOM COOLING PEAK COIL COOLING PEAK COIL HTG. PEAK
Zone Name Room Name Mult. CFM Sensible I Latent CFM I Sensible Latent CFM Sensible
Existing 1st Floor Existing 1stFloor 1 1,073 21,906 886 1,073 21,906 886 808 30,656
1st Floor Addition 1st Floor Addition 1 1 172 3,5161 261 172 3,516 261 131 4,977
I , Total includes ventilation load for zonal
C WAT E FRMAJO
Building ftpArtmem-
Reviewed By: Sean Hatch
Date: 05/11/16
1,245
25,423
1,146
940
35,634
1,245
25,423
1,146
940
35,634