15070021CITY OF CUPERTINO BUILDING PERMIT
BUILDING ADDRESS:
CONTRACTOR:
PERMIT NO: 15070021
10320 MORETTI DR CUPERTINO CA 95014 (375 15 009)
(CHEN'S
CONSTRUCTION
COMPANY)
SAN JOSE, CA 95130
OWNER'S NAME: ( LAI LEE JEE-JEAN TRUSTEE)
DATE ISSUED:
OWNER'S PHONE:
PHONE NO:
LICENSED CONTRACTOR'S DECLARATION
BUILDING PERMIT INFO:
License Class Lia #
Contractor (CHEN'S CONSTRUCTION COMPANY) Date
—BLDG —ELECT —PLUMB
I hereby affirm that I am licensed under the previsions of Chapter 9 (commencing
MECH _ RESIDENTIAL _ COMMERCIAL
with Section 7000) of Division 3 of the Business & Professions Code and that my
license is in full force and effect.
JOB DESCRIPTION:
CONSTRUCT N 1 STORY SFD WITH 1,965 S.F. LIVING
I hereby affirm under penalty of perjury one of the following two declarations:
SPACE, 452 S.F. GARAGE & 40 S.F. PORCH/DECKS
r. I have and wilt maintain a certificate of consent to self -insure for Worker's
(2,457 COMBINED)**SUNNYVALE SANITARY**
Compensation, as provided for by Section 3700 of the Labor Code, for the
performance of the work for which this permit is issued.
2. I have and will maintain Worker's Compensation Insurance, as provided for
by Section 3700 of the Labor Code, for the performance of the work for which
Sq. Ft Floor Area:
Valuation: $365000.00
this permit is issued.
APPLICANT CERTIFICATION
certify that I have read this application and state that the above
information is correct. I agree to comply with all city and county
APN Number:
Occupancy Type:
ordinances and state laws relating to building construction, and hereby
375 15 009
authorize representatives of this city to enter upon the above mentioned
property for inspection purposes. (We) agree to save indemnify and keep
harmless the City of Cupertino against liabilities, judgments, costs, and
PERMIT EXPIRES IF WORK IS NOT STARTED
expenses which may accrue against said City in consequence of the
WITHIN 180 DAYS OF PERMIT ISSUANCE 012
granting of this permit. Additionally, the applicant understands and will
comply with all non -point source regulations per the Cupertino Municipal
180 DAYS FROM LAST CALLED INSPECTION.
Code, Section 9.18.
Issued by: -1
Signature Date
Date:
OWNER -BUILDER DECLARATION
RE -ROOFS:
I hereby affirm that I am exempt from the Contractor's License Law for one of the
All roofs shall be inspected prior to any roofing material being installed. If a roof is
following two reasons:
installed without first obtaining an inspection,. I agree to remove all new materials for
1. I, as owner of the properly, or my employees with wages as their sole
inspection.
compensation, will do the work, and the structure is not intended or offered
for sale (Sec.7044; Business & Professions Code)
Signature of Applicant
2. I, as owner of the property, am exclusively contracting with licensed
Date:
contractors to construct the project (Sec. 7044, Business & Professions Code).
ALL ROOF COVERINGS TO BE CLASS "A" OR BETTER
I hereby affirm under penalty of perjury one of the following three declarations:
1. I have and will maintain a Certificate of Consent to self -insure for Worker's
Compensation, as provided for by Section 3700 of the Labor Code, for the
HAZARDOUS MATERIALS DISCLOSURE
performance of the work for which this permit is issued.
I have read the hazardous materials requirements under Chapter 6.95 of the
2. I have and will maintain Worker's Compensation Insurance, as provided for
California Health & Safety Code, Sections 25505, 25533, and 25534. 1 will
by Section 3700 of the Labor Code, for the performance of the work for which
maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and the
Health & Safety Code, Section 25532(x) should I store or handle hazardous
this permit is issued.
material. Additionally, should I use equipment or devices which emit hazardous
3. I certify that in the performance of the work for which this permit is issued, I
air contaminants as defined by the Bay Area Air Quality Management District I
shall not employ any person in any manner so as to become subject to the
will maintain compliance with the Cupertino Municipal Code, Chapter 9,12 and
Worker's Compensation laws of California. If, after making this certificate of
the Health & Safety Code, Sections 25505, 25533, and 25534.
exemption, I become subject to the Worker's Compensation provisions of the
Labor Code, I must forthwith comply with such provisions or this permit shall
Owner or authorized agent:
be deemed revoked.
Date:
APPLICANT CERTIFICATION
CONSTRUCTION LENDING AGENCY
I hereby affirm that there is a construction lending agency for the performance
I certify that I have read this application and state that the above information is
of work's for which this permit is issued (Sec. 3097, Civ C.)
correct. I agree to comply with all city and county ordinances and state laws
relating to building construction, and hereby authorize representatives of this city
Lender's Name
to enter upon the above mentioned property for inspection purposes. (We) agree
Lender's Address
to save indemnify and keep harmless the City of Cupertino against liabilities,
judgments, costs, and expenses which may accrue against said City in
ARCHITECT'S DECLARATION
consequence of the granting of this permit. Additionally, the applicant
I understand my plans shall be used as public records.
understands and will comply with all non -point source regulations per the
Cupertino Municipal Code, Section 9.18.
Licensed
Professional
Signature Date
CUPERTINO
CONTRACTOR / SUBCONTRACTOR LIST
Building Department
City Of Cupertino
10300 Torre Avenue
Cuertno, CA 95014-3255
I hone: 408-777-3228
Fax: 408-777-3333
JOB ADDRESS:PERMIT#
SUBCONTRACTOR
BUSINESS NAME
OWNER'S NAM e: LAI LEFE aSC
LICENSE
GENERAL CONTRACTOR- CA /, Cno. Gcct�_av_�
-PHONE#
BUSINESS LICENSE #
ADDRESS: lVoMaJ8v
CITY/ZIPCODE:
Cement Finishing
--- --ill-wal —quiles an ijusinesse4iworiung in tne city to nave a Uity of Cupertino,b siness license.
NO BUILDING FINAL OR FINAL OCCUPANCY INSPECTION(S) WILL BE SCHEIIULED UNTIL THE
GENERAL CONTRACTOR AND ALL SUBC ,NTRACTORS HAVE OBTAINED A CITY OF CUPERTINO
BUSINESS LICENSE.
I am not using any subcontractors:> 3
Signature hate
Please check applicable subcontractors and complete the following information:
V
SUBCONTRACTOR
BUSINESS NAME
BUSINESS
LICENSE
Cabinets & Millwork
Cement Finishing
1 Electrical
Excavation,
Fencing
Flooring / Carpeting
Linoleum / Wood
Glass Glazing
Heating
Insulation
Landscaping
Lathing
Masonry
Painting Wallpaper
Paving
Plastering
Plumbing
Roofing
Septic Tank
Sheet Metal
,Sheet Rock
Tile
Owner / Contractor Signature Date
CITY OF CUPERTINO BUILDING PERMIT I
BUILDING ADDRESS: CONTRACTOR: PERMIT NO: 15070021
10320 MORETTI DR CUPERTINO CA 95014 (375 15 009) (CHEN'S
CONSTRUCTION
COMPANY)
SAN JOSE, CA 95130
OWNER'S NAME: ( LAI LEE JEE-JEAN TRUSTEE) DATE ISSUED:
OWNER'S PHONE:
LICENSED CONTRACTOR'S DECLARATION
License Class Lic. # �% 0 t' 1 i L G]
I� i b
Contractor (CHES CENSTRUCTI•N ,
WY Date
I hereby affirm that I am licensed under the provisions of Chapter 9 (commencing
with Section 7000) of Division 3 of the Business & Professions Code and that my
license is in full force and effect.
IMI:
BUILDING PERMIT INFO:
BLDG —ELECT -PLUMB
MECH _ RESIDENTIAL _ COMMERCIAL
JOB DESCRIPTION:
CONSTRUCT (N) 1 STORY SFD WITH 1,965 S.F. LIVING
I hereby affirm under penalty of perjury one of the following two declarations: SPACE, 452 S.F. GARAGE & 40 S.F. PORCHIDECKS
i. I have and will maintain a certificate of consent to self -insure for Worker's (2,457 COMBINED)' 'SUNNYVALE SANITARY"
Compensation, as provided for by Section 3700 of the Labor Code, for the
performance of the work for which this permit is issued.
I have and will maintain Worker's Compensation Insurance, as provided for
VI _ by Section 3700 of the Labor Code, for the performance of the work for which
this permit is issued. Sq. Ft Floor Area: Valuation: $365000.00
APPLICANT CERTIFICATION
I certify that I have read this application and state that the above
information is correct. I agree to comply with all city and county
ordinances and state laws relating to building construction, and hereby
authorize representatives of this city to enter upon the above mentioned
property for inspection purposes. (We) agree to save indemnify and keep
harmless the City of Cupertino against liabilities, judgments, costs, and
expenses which may accrue against said City in consequence of the
granting of this permit. Additionally, the applicant understands and will
comply with all non -point source regulations per the Cupertino Municipal
Code, Section 9.18. n
Signature {C 4tDate
I hereby affirm that I am exempt from the Contractor's License Law for one of the
following two reasons:
1. I, as owner of the property, or my employees with wages as their sole
compensation, will do the work, and the structure is not intended or offered
for sale (Sec.7044, Business & Professions Code)
I, as owner of the property, am exclusively contracting with licensed
contractors to construct the project (Sec.7044, Business & Professions Code).
hereby affirm under penalty of perjury one of the following three declarations:
1. I have and will maintain a Certificate of Consent to self -insure for Worker's
Compensation, as provided for by Section 3700 of the Labor Code, for the
performance of the work for which this permit is issued.
2. I have and will maintain Worker's Compensation Insurance, as provided for
by Section 3700 of the Labor Code, for the performance of the work for which
this permit is issued.
s. I certify that in the performance of the work for which this permit is issued, I
shall not employ any person in any manner so as to become subject to the
Worker's Compensation laws of California. If, after making this certificate of
exemption, I become subject to the Worker's Compensation provisions of the
Labor Code, I must forthwith comply with such provisions or this permit shall
be deemed revoked.
APPLICANT CERTIFICATION
I certify that I have read this application and state that the above information is
correct. I agree to comply with all city and county ordinances and state laws
relating to building construction, and hereby authorize representatives of this city
to enter upon the above mentioned property for inspection purposes. (We) agree
to save indemnify and keep harmless the City of Cupertino against liabilities,
judgments, costs, and expenses which may accrue against said City in
consequence of the granting of this permit. Additionally, the applicant
understands and will comply with all non -point source regulations per the
Cupertino Municipal Code, Section 9.18.
Sig
Date
APN Number: Occupancy Type:
375 15 009
PERMIT EXPIRES IF WORK IS NOT STARTED
WITHIN 180 DAYS OF PERMIT ISSUANCE OR
180 DAYS FR^". �f' o i' CALLED INSPECTION.
lnwtl-13y: -� �_� 1119116
Date:
RE -ROOFS:
All roofs shall be inspected prior to any roofing material being installed. If a roof is
installed without fust obtaining an inspection, I agree to remove all new materials for
inspection.
Signature of
Date:
ALL ROOF COVERINGS TO BE CLASS "A" OR BETTER
HAZARDOUS MATERIALS DISCLOSURE
I have read the hazardous materials requirements under Chapter 6.95 of the
California Health & Safety Code, Sections 25505, 25533, and 25534. I will
maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and the
Health & Safety Code, Section 25532(a) should I store or handle hazardous
material. Additionally, should I use equipment or devices which emit hazardous
air contaminants as defined by the Bay Area Air Quality Management District I
will maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and
the Health & Safety Code, Sections 25505, 251-33, and 25534.
Owner or authorized agent:
Date:
< < M�CONSTRUCTION LENDING AGENCY
I hereby affirm that there is a construction lending agency for the performance
of work's for which this permit is issued (Sec. 3097, Civ C.)
Lender's Name
Lender's Address
ARCHITECT'S DECLARATION
understand my plans shall be used as public records.
Licensed
Professic
CONSTRUCTION PERMIT APPLICATION
COMMUNITY DEVELOPMENT DEPARTMENT • BUILDING DIVISION
10300 TORRE AVENUE • CUPERTINO, CA 95014-3255
(408) 777-3228 •FAX (408) 777-3333 • building(-cupertino.org / S
0CU/PERTlN4
NEW CONSTRUCTION El ADDITION ❑ALTERATION / TI ❑ REVISION/ DEFERRED ORIGINAL PERMIT 4
PROJECT ADDRESS D ] ^ O p `/�
r
O D
APN # 5-- 1,5--
OWNER NAME oM PHONE n
E-MAIL wpb.
STREET ADDRESS � � I,G
CITY, STATE, ZIP d FAX
V
-�
PHONED� E-MAIL��
CONTACT NAME-� �
I
STREET ADDRESS J_ /1
'��Vo'A ky
�❑l
CITY, STATE, ZIP- �r°�
/l 71
FAX
Om" 11 OWNER -BUDDER ❑ ONTcRAGENr CONTRACTOR ❑ CONTRACTOR AGENT ❑ ARCHrrFcT ❑ ENGINEER ❑ DEVELOPER ❑ TENANT
CONTRACTOR NAME
•
LICENSE NUMBER
LICENSE TYPE
BUS. LIC #
COMPANY NAME
E-MAIL
FAX
STREET ADDRESS
CITY, STATE, ZIP
PHONE
ARCHITECTIENGINEER NAME LICENSE NUMBER
BUS. LIC #
COMPANY NAME
E-MAIL
FAX
STREET ADDRESS
CITY, STATE, ZIP
PHONE
DESCRIPTION OF WORK� � e �
_ c
L) lbor 920 k5F ()�-ge
TO4-ish -t /1/kbe— 1 % S (4 c - C'✓`� 7f
EXISTING USE
PROPOSED USECONSTR
TYPE # STORIES
USE TYPE I OCC.
SQ.FT.
VALUATION (S)
AREA /
AREA/ 1 L
7
NEWNEWFLOOR
AREA 1
dKITCHEN
DEMO /
AREA
BATHROOM
OTHER
REMODEL AREA
REMODEL AREA
REMODEL AREA
PORCH AREA
DECK AREA
TOTAL DECK/PORCH ARE I GARAGE AREA: DETACH
'LOC
W,45,4- REATTACH
# DWELLA'G UNITS:
IS A SECONDUNIT ❑ YES
SECOND STORY []YES/
BErNGADDED? . �No
ADDITION? ; NO
PRE -APPLICATION ❑ YES IF YES, PROVIDE COPY OFt"SICTER
PLANNGAPPL# RINO PLANNINGAPPROVALLETTERHOME?
BLDG AN 11YES
NOM
''
QLD - OTAL VALUAT N: O0
By my signature below, I certify to each of the following: I am the property owror authorize aeent to ac a owner's behalf. I have read this
application and the information I have provided is correct. I }lave read the Description of Work and verify urate. I agree to comply with all applicable local
ordinances and state laws relating to buuilding constru n. I aukhorize representatives -of Cupertino to enter the above- tified op rt for in ection purposes.
Signature of Applicant/Agent: Date:! 9
SUPPLEMENTAL IIRFORMATION REQUIRED
New SFD or Multifamily dwellings: Apply for demolition permit for
existing building(s). Demolition permit is required prior to issuance of buildir-
permit for new building
_ Commercial Bldgs: Provide a completed Hazardous Materials Disclosure
<r,v, �,i;u,
_
form if any Hazardous Materials are being used as part of this project.
_ Copy of Planning Approval Letter or Meeting with Planning prior to
submittal of Building Permit application.
BldgApp_2011.doc revised 06/21/11
SF
RPM��,M CITY OF CUPERTINO
FEE ESTIMATOR - BUILDING DIVISION
OCCUPANCY TYPE:
ADDRESS: 10320 MORETTI DR
DATE: 07/06/2015
REVIEWED BY: MELISSA
PC FEE ID
APN: 37515 009
BP#:
'VALUATION: 1$365,000
*PERMIT TYPE: Building Permit
PLAN CHECK TYPE: New Construction
PRIMARY
USE: SFD or Duplex
2nd Unit? Yes No
PENTAMATION
PERMIT TYPE: 1 R3SFD
WORK
CONSTRUCT N 1 STORY SFD WITH 1,974 S.F. LIVING SPACE 452 S.F. GARAGE & 80 S.F.
SCOPE I
PORCH/DECKS (2,506 COMBINED)
OCCUPANCY TYPE:
TYPE OF
CONSTR.
FLR AREA
s.f.
PC FEES
PC FEE ID
BP FEES
BP FEE ID
R-3 (Custom)
II-B,111-B,IV,V-B
2,506
$2,984.61
IR3PLNCK
$2,821.63
1R31NSP
Permit Fee:
$2,821.63
Suppl. Insp. Fee -0 Reg. 0 OT
0.0
hrs
$0.00
PME Unit Fee:
$0.00
PME Permit Fee:
$0.00
Construction Tax: IBCONSTAXR
1"
# new units
$684.98
Administrative 1,ee:
0
O
Work Without Permit? 0 Yes No
$0.00
TOTALS:
2,506
$2,984.61
i"ruvc�l L7vcutnc�nlalirtn 1
$2,821.63
Strong Motion Fee: IBSEISMICR
NOTE: This estimate does not include fees due to other Departments (i.e. Planning, Public Works, Fire, Sanitary Sewer District, School
Lstrirt ot.- )_ neve feet aro hated an the nreliminary information available and are only an estimate. Contact the Dept for addn'1 info.
FEE ITEMS (Fee Resolution 11-053 fff. 711113)
Afech. Plan Check
Plumb. flan Check
ec. Plan Check
;bfecI, Permit Fee:
Plug.
Elec. Permit Fee
Other Alcch. Ins)
Other Plumb Ing?Ll
Other lilec. Insp. E17--
3dech. Insp. Pee:
Plumb. Insp. Hee:
Elec. Insp. Fee:
NOTE: This estimate does not include fees due to other Departments (i.e. Planning, Public Works, Fire, Sanitary Sewer District, School
Lstrirt ot.- )_ neve feet aro hated an the nreliminary information available and are only an estimate. Contact the Dept for addn'1 info.
FEE ITEMS (Fee Resolution 11-053 fff. 711113)
FEE
QTY/FEE
MISC ITEMS
Plan Check Fee:
$2,984.61
Select a Misc Bldg/Structure
or Element of a Building
Supp/. PC Fee: Q Reg. ®OT
0.0
hrs
$0.00
PME Plan Check:
$0.00
Permit Fee:
$2,821.63
Suppl. Insp. Fee -0 Reg. 0 OT
0.0
hrs
$0.00
PME Unit Fee:
$0.00
PME Permit Fee:
$0.00
Construction Tax: IBCONSTAXR
1"
# new units
$684.98
Administrative 1,ee:
0
O
Work Without Permit? 0 Yes No
$0.00
Advanced Planning Fee: IPLLONGR
$350.84
Select a Non -Residential Q
Building or Structure 0
i
i"ruvc�l L7vcutnc�nlalirtn 1
Strong Motion Fee: IBSEISMICR
$47.45
Select an Administrative Item
Bldg Stds Commission Fee: IBCBSC
$15.00
SUBTOTALS:
$6,904.51
$0.00
TOTAL FEE:
$6,904.51
Revised: 07/02/2015
2013 Low -Rise Residential Mandatory Measures Summary
NOTE: Low-rise residential buildings subject to the Standards must comply with all applicable mandatory measur : e ,s t e
com liance a roach used Face tions ma a Iv. Review the res ective code section or more in orodtion. �
Building Envelope Measures:
§ 110.6(a)1:
Doors and windows between conditioned and unconditioned spaces are manufactured to limit air leakage.
Fenestration products (except field -fabricated windows) have a label listing the certified U -Factor, certified Solar Heat Gain
§ 110.6(a)5:
Coefficient SHGC , and infiltration that meets the requirements of § 10-111 (a).
§ 110.7:
Exterior doors and windows are weatherstripped; all joints and penetrations are caulked and sealed.
§I 10.8(a):
Insulation specified or installed meets Standards for Insulating Material. Indicate type and include on the CF2R.
The thermal emittance and aged solar reflectance values of the cool roofing material meets the requirements of §1 10.8(i) when the
§ 110.8(1):
installation of a cool roof is specified on the CF 1 R.
§110.80):
A radiant barrier shall have an emittance of 0.05 or less when the installation of a radiant barrier is specified on the CF1R.
Minimum R-30 insulation in wood -frame ceiling; or the weighted average U -factor shall not exceed 0.031. Minimum R-19 in a
§150.0(a):
rafter roof alteration. Attic access doors shall have permanently attached insulation using adhesive or mechanical fasteners. The
attic access shall be gasketed to prevent air leakage.
§150.0(b):
Loose fill insulation shall conform with manufacturer's installed design labeled R -value.
Minimum R-13 insulation in 2x4 inch wood framing wall or have a U -factor of 0.102 or less (R-19 in 2x6 or 0.074 maximum U -
§ 150.0(c):
factor).
§150.0(d):
Minimum R-19 insulation in raised wood -frame floor or 0.037 maximum U -factor.
In Climate Zones 14 and 16 a Class II vapor retarder shall be installed on the conditioned space side of all insulation in all exterior
§150.0(g)l:
walls, vented attics and unvented attics with air -permeable insulation.
In Climate Zones 1-16 with unvented crawl spaces the earth floor of the crawl space shall be covered with a Class I or Class II
§ 150.0(g)2:
vapor retarder.
In a building having a controlled ventilation crawl space, a Class I or Class II vapor retarder shall be placed over the earth floor of
§ 150.0(g)3:
the crawl space to reduce moisture entry and protect insulation from condensation, as specified in the exception to Section
150.0(d).
Slab edge insulation shall: have a water absorption rate, for the insulation material alone without facings, no greater than 0.3%;
§150.0(1):
have water vapor permeance rate is no greater than 2.0 perm/inch, be protected from physical damage and UV light deterioration;
and when installed as part of a heated slab floor meets the requirements of § 110.8
Fenestr including skylights, separating conditioned space from unconditioned space or outdoors shall have a maximum U -
§ 150.0(q):
factor o var e U -factor of all fenestration shall not exceed 0.58.
Fireplaces, Decorative Gas Appliances and &Mg Measures:
§150.0(e)IA:
Masonry oJf1pt2ff-k!$& e laces have a closable metal or glass door covering the entire opening of the firebox.
Masonry or factofy-NAMWplaces have a combustion outside air intake, which is at least six square inches in area and is
§150.0(e)1B:
equipped with a re ily accessible, operable, and tight -fitting damper or a combustion -air control device.
§ 150.0(e)IC:
MasontylWactory-built fireplaces have a flue damper with a readily accessible control.
Continuous burning,'p-36-f1ights and the use of indoor air for cooling a firebox jacket, when that indoor air is vented to the outside
§ 150.0(e)2:11
of the building, are prohibited.
Space Conditioning, Water Heating and Plumbing System Measures:
§ 110.0-§ 110.3:
HVAC equipment, water heaters, showerheads, faucets and all other regulated appliances are certified to the Energy Commission.
Water heating recirculation loops serving multiple dwelling units meet the air release valve, backflow prevention, pump isolation
§ 110.3(c)5:
valve, and recirculation loop connection requirements of §I 10.3(c)5.
Continuously buming pilot lights are prohibited for natural gas: fan -type central f imaces, household cooking appliances (appli-
§110.5:
ances without an electrical supply voltage connection with pilot lights that consume less than 150 Btu/hr are exempt), and pool
ands a heaters.
Heating and/or cooling loads are calculated in accordance with ASHRAE, SMACNA or ACCA using design conditions specified
§150.0(h)l:
in § 150.0(h)2.
Installed air conditioner and heat pump outdoor condensing units shall have a clearance of at least five feet from the outlet of any
§ 150.0(h)3A:
dryer vent.
§ 150.0(i):
Heating systems are equipped with thermostats that meet the setback requirements of § 110.2(c).
Storage gas water heaters with an energy factor equal to or less than the federal minimum standards shall be externally wrapped
§ 150.00)1 A:
with insulation having an installed thermal resistance of R-12 or greater.
Unfired hot water tanks, such as storage tanks and backup storage tanks for solar water -heating systems, have R-12 external
§150.0(j)1B:
insulation or R-16 internal insulation where the internal insulation R -value is indicated on the exterior of the tank.
For domestic hot water system piping, whether buried or unburied: the first 5 feet of hot and cold water pipes from the storage
tank, all piping with a nominal diameter of 3/4 inch or larger, all piping associated with a domestic hot water recirculation system
§ 150.00)2A:
regardless of the pipe diameter, piping from the heating source to storage tank or between tanks, piping buried below grade, and
all hot water pipes from the heating source to kitchen fixtures must be insulated according to the requirements of TABLE 120.3-
A.
All domestic hot water pipes that are buried below grade must be installed in a water proof and non -crushable casing or sleeve
§ 150.00)2B:
that allows for installation, removal, and replacement of the enclosed pipe and i a
2013 Low -Rise Residential Mandatory Measures Summary
§ 150.00)2C:
Pipe for cooling system lines shall be insulated as specified in § I50.00)2A. Piping insulation for steam and hydronic heating
systems or hot waters stems with pressure > 15 psig shall meet the requirements in TABLE 120.3-A.
§150.00)3:
Insulation is protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind.
Insulation exposed to weather shall either be rated for outdoor use or installed with a cover suitable for outdoor service. For
§ 150.00)3A:
example, protected by aluminum, sheet metal, painted canvas, or plastic cover. Cellular foam insulation protected as specified or
painted with coating that is water retardant and provides shielding from solar radiation that degrades the material.
Insulation covering chilled water piping and refrigerant suction piping located outside the conditioned space shall have a Class I
§ 150.00)3B:
or Class II vapor retarding facing, or the insulation shall be installed at the thickness that qualifies as a Class I or Class II vapor
retarder.
Systems using gas or propane water heaters to serve individual dwelling units shall include: a 120V electrical receptacle within 3
feet of the water heater; a Category III or IV vent, or a Type B vent with straight pipe between the outside termination and the
§150.0(n)l:
space where the water heater is installed; a condensate drain that is no more than 2 inches higher than the base of the installed
water heater, and allows natural draining without pump assistance; and a gas supply line with a capacity of at least 200,000
Btu/hr.
§150.0(n)2:
Recirculating loops serving multiple dwelling units shall meet the requirements of § 110.3(c)5.
§150.0(n)3:
Solar water -heating systems and collectors shall be certified and rated by the Solar Rating and Certification Corporation (SRCC)
or by a testing agency approved by the Executive Director.
Ducts and Fans Measures:
All air -distribution system ducts and plenums installed are sealed and insulated to meet the requirements of CMC §601.0, §602.0.
§603.0, §604.0, §605.0 and ANSUSMACNA-006-2006 HVAC Duct Construction Standards Metal and Flexible 3rd Edition.
Supply -air and return -air ducts and plenums are insulated to a minimum installed level of R-6.0 (or higher if required by CMC
§605.0) or enclosed entirely in directly conditioned space as confirmed through field verification and diagnostic testing
(RA3.1.4.3.8). Connections of metal ducts and inner core of flexible ducts are mechanically fastened. Openings shall be sealed
§150.0(m)l:
with mastic, tape, or other duct -closure system that meets the applicable requirements of UL 181, UL 181A, or UL 181B or
aerosol sealant that meets the requirements of UL 723. If mastic or tape is used to seal openings greater than '/4 inch, the
combination of mastic and either mesh or tape shall be used. Building cavities, support platforms for air handlers, and plenums
defined or constructed with materials other than sealed sheet metal, duct board or flexible duct shall not be used for conveying
conditioned air. Building cavities and support platforms may contain ducts. Ducts installed in cavities and support platforms
shall not be compressed to cause reductions in the cross-sectional area of the ducts.
Factory -Fabricated Duct Systems shall comply with specified requirements for duct construction, connections, and closures; joints
§ 150.0(m)2:
and seams of duct systems and their components shall not be sealed with cloth back rubber adhesive duct tapes unless such tape is
used in combination with mastic and draw bands.
§150.0(m)3-6:
Field -Fabricated Duct Systems shall comply with requirements for: pressure -sensitive tapes, mastics, sealants, and other
requirements specified for duct construction; duct insulation R -value ratings; duct insulation thickness; and duct labeling.
§150.0(m)7:
All fan systems that exchange air between the conditioned space and the outside of the building must have backdraft or automatic
dampers.
§ 150.0(m)8:
Gravity ventilating systems serving conditioned space have either automatic or readily accessible, manually operated dampers
except combustion inlet and outlet air openings and elevator shaft vents.
Insulation shall be protected from damage, including that due to sunlight, moisture, equipment maintenance, and wind but not
§ 150.0(m)9:
limited to the following: insulation exposed to weather shall be suitable for outdoor service. For example, protected by aluminum,
sheet metal, painted canvas, or plastic cover. Cellular foam insulation shall be protected as above or painted with a coating that is
water retardant and provides shielding from solar radiation.
§150.0(m)10:
Flexible ducts cannot have porous inner cores.
When space conditioning systems use forced air duct systems to supply conditioned air to an occupiable space, the ducts shall be
§ 150.0(m)11:
sealed and duct leakage tested, as confirmed through field verification and diagnostic testing, in accordance with Reference
Residential Appendix RA3.
Mechanical systems that supply air to an occupiable space through ductwork exceeding 10 feet in length and through a thermal
§150.0(m)12:
conditioning component, except evaporative coolers, shall be provided with air filter devices that meet the requirements of
§150.0(m)12.
Space conditioning systems that utilize forced air ducts to supply cooling to an occupiable space shall have a hole for the
placement of a static pressure probe (HSPP), or a permanently installed static pressure probe (PSPP) in the supply plenum. The
§ I50.0(m)13:
space conditioning system must also demonstrate airflow > 350 CFM per ton of nominal cooling capacity through the return
grilles, and an air -handling unit fan efficacy:5 0.58 W/CFM as confirmed by field verification and diagnostic testing, in
accordance with Reference Residential Appendix RA3.
Zonally controlled central forced air cooling systems shall be capable of simultaneously delivering, in every zonal control mode,
§150.0(m)15:
an airflow from the dwelling, through the air handler fan and delivered to the dwelling, of >_ 350 CFM per ton of nominal cooling
capacity, and operating at an air -handling unit fan efficacy of <_ 0.58 W/CFM as confirmed by field verification and diagnostic
testing, in accordance with Reference Residential Appendix RA3.
All dwelling units shall meet the requirements of ASHRAE Standard 62.2. Neither window operation nor continuous operation of
§150.0(o):
central forced air system air handlers used in central fan integrated ventilation systems are permissible methods of providing the
Whole Building Ventilation.
§150.0(o)IA:
Whole Building Ventilation airflow shall be confirmed through field verification and diagnostic testing, in accordance with
Reference Residential Appendix RA3.
Pool and Spa Heating Systems and Equipment Measures:
Any pool or spa heating system shall be certified to have: a thermal efficiency that complies with the Appliance Efficiency
§ 110.4(a):
Regulations; an on-off switch mounted outside of the heater that allows shutting off the heater without adjusting the thermostat
setting; a permanent weatherproof plate or card with operating instructions; and shall not use electric resistance heating.
2013 Low -Rise Residential Mandatory Measures Summary
§ 110.4(b)1:
Any Pool or spa heating equipment shall be installed with at least 36 inches of pipe between filter and heater or dedicated suction
and return lines, or built-up connections for future solar heating.
§ 110.4(b)2:
Outdoor pools or spas that have a heat pump or gas heater shall have a cover.
§ 110.4(b)3:
Pools shall have directional inlets that adequately mix the pool water, and a time switch that will allow all pumps to be set or pro-
grammed to run only during off-peak electric demand periods.
§ 110.5:
Natural gas pool and spa heaters shall not have a continuous burning pilot light.
§ 150.0(p):
Residential pool systems or equipment shall meet specified pump sizing, flow rate, piping, filters, and valve requirements.
Lighting Measures:
§ 110.9:
All lighting control devices and systems, ballasts, and luminaires shall meet the applicable requirements of § 110.9.
§150,0(k)IA:
Installed luminaires shall be classified as high -efficacy or low -efficacy for compliance with §150.0(k) in accordance with TABLE.
150.0-A or TABLE 150.0-B, as applicable.
§150.0(k)IB:
When a high efficacy and low efficacy lighting system are combined in a single luminaire, each system shall separately comply
with the applicable provisions of § 150.0(k).
The wattage and classification of permanently installed luminaires in residential kitchens shall be determined in accordance with
§ 150.0(k)1C:
§ I30.0(c). In residential kitchens, the wattage of electrical boxes finished with a blank cover or where no electrical equipment has
been installed, and where the electrical box can be used for a luminaire or a surface mounted ceiling fan, shall be calculated as 180
watts of low efficacy lighting r electrical box.
§ 150.0(k)iD:
Ballasts for fluorescent lamps rated 13 watts or greater shall be electronic and shall have an output frequency no less than 20 kHz.
Permanently installed night lights and night lights integral to installed luminaires or exhaust fans shall be rated to consume no
§ 150.0(k)IE:
more than 5 watts of power per luminaire or exhaust fan as determined in accordance with § I30.0(c). Night lights do not need to
be controlled by vacancy sensors.
§ 150.0(k)1F:
Lighting integral to exhaust fans (except when installed by the manufacturer in kitchen exhaust hoods) shall meet the applicable
requirements of § 150.0(k).
§ 150.0(k)2A:
High efficacy luminaires must be switched separately from low efficacy luminaires.
§ 150.0(k)2B:
Exhaust fans shall be switched separately from lighting systems.
§ I50.0(k)2C:
Luminaires shall be switched with readily accessible controls that permit the luminaires to be manually switched ON and OFF.
§ 150.0(k)2D:
Controls and equipment are installed in accordance with manufacturer's instructions.
§150.0(k)2E:
No control shall bypass a dimmer or vacancy sensor function if the control is installed to comply with §I50.0(k).
§150.0(k)2F:
Lighting controls comply with applicable requirements of §110.9.
An Energy Management Control System (EMCS) may be used to comply with dimmer requirements if. it functions as a dimmer
§ 150.0(k)2G:
according to § 110.9; meets Installation Certificate requirements of § 130.4; the EMCS requirements of §130.5; and all other
requirements in §150.0(k)2.
An Energy Management Control System (EMCS) may be used to comply with vacancy sensor requirements of § I50.0(k) if. it
§ 150.0(k)2H:
functions as a vacancy sensor according to § 110.9; meets Installation Certificate requirements of § 130.4; the EMCS requirements
of 130.5; and all other requirements in §150.0(k)2.
§ I50.0(k)2I:
A multiscene programmable controller may be used to comply with dimmer requirements of this section if it provides the
functionality of a dimmer according to § 110.9, and complies with all other applicable requirements in §150.0(k)2.
§ 150.0(k)3A:
A minimum of 50 percent of the total rated wattage of permanently installed lighting in kitchens shall be high efficacy.
Kitchen lighting includes all permanently installed lighting in the kitchen except internal lighting in cabinets that illuminate only
§ 150.0(k)3B:
the inside of the cabinets. Lighting in areas adjacent to the kitchen, including but not limited to dining and nook areas, are
considered kitchen lighting if they are not separately switched from kitchen lighting.
§I50.0(k)4:
Permanently installed lighting that is internal to cabinets shall use no more than 20 watts of power per linear foot of illuminated
cabinet.
§ I50.0(k)5:
A minimum of one high efficacy luminaire shall be installed in each bathroom; and all other lighting installed in each bathroom
shall be high efficacy or controlled by vacancy sensors.
§ 150.0(k)6:
Lighting installed in attached and detached garages, laundry rooms, and utility rooms shall be high efficacy luminaires and
controlled by vacancy sensors.
§ 150.0(k)7:
Lighting installed in rooms or areas other than in kitchens, bathrooms, garages, laundry rooms, and utility rooms shall be high
efficacy, or shall be controlled by either dimmers or vacancy sensors.
Luminaires recessed into ceilings shall: be listed for zero clearance insulation contact (IC) by Underwriters Laboratories or other
nationally recognized testing/rating laboratory; have a label that certifies that the luminaire is airtight with air leakage less than 2.0
CFM at 75 Pascals when tested in accordance with ASTM E283; be sealed with a gasket or caulk between the luminaire housing
§ 150.0(k)8:
and ceiling, and shall have all air leak paths between conditioned and unconditioned spaces sealed with a gasket or caulk; and
allow ballast maintenance and replacement without requiring cutting holes in the ceiling.
For recessed compact fluorescent luminaries with ballasts to qualify as high efficacy for compliance with §150.0(k), the ballasts
shall be certified to the Energy Commission to comply with the applicable requirements in § 110.9.
For single-family residential buildings, outdoor lighting permanently mounted to a residential building or other buildings on the
same lot shall be high efficacy, or may be low efficacy if it meets all of the following requirements:
i. Controlled by a manual ON and OFF switch that does not override to ON the automatic actions of Items ii or iii below; and
§ 150.0(k)9A:
ii. Controlled by a motion sensor not having an override or bypass switch that disables the motion sensor, or controlled by a
motion sensor having a temporary override switch which temporarily bypasses the motion sensing function and automatically
reactivates the motion sensor within 6 hours; and
iii. Controlled by one of the following methods:
2013 Low -Rise Residential Mandatory Measures Summary
a. Photocontrol not having an override or bypass switch that disables the photocontrol; or
b. Astronomical time clock not having an override or bypass switch that disables the astronomical time clock, and which is
programmed to automatically turn the outdoor lighting OFF during daylight hours; or
c. Energy management control system which meets all of the following requirements: At a minimum provides the functionality of
an astronomical time clock in accordance with §110.9; meets the Installation Certification requirements in §130.4; meets the
requirements for an EMCS in § 130.5; does not have an override or bypass switch that allows the luminaire to be always ON; and,
is programmed to automatically turn the outdoor lighting OFF during daylight hours.
For low-rise multifamily residential buildings, outdoor lighting for private patios, entrances, balconies, and porches; and outdoor
lighting for residential parking lots and residential carports with less than eight vehicles per site shall comply with one of the
§ 150.0(k)9B:
following requirements:
i. Shall comply with § 150.0(k)9A; or
ii. Shall comply with the applicable requirements in 110.9, 130.0, §1 0.2, 130.4, 140.7 and 141.0.
For low-rise residential buildings with four or more dwelling units, outdoor lighting not regulated by § 150.0(k)9B or 150.0(k)9D
§ 150.0(k)9C:
shall comply with the applicable requirements in § 110.9, § 130.0, § 130.2, § 130.4, § 140.7 and § 141.0.
Outdoor lighting for residential parking lots and residential carports NN ith a total of eight or more vehicles per site shall comply
§ 150.0(k)9D:
with the applicable requirements in ' 110.9, § 130.0, § 130.2, § 130.4, § 140.7 and § 141.0.
Internally illuminated address signs shall comply with §140.8; or shall consume no more than 5 watts of power as determined
§150.0(k)10:
according to § 130.0(c).
Lighting for residential parking garages for eight or more vehicles shall comply with the applicable requirements for
§ 150.0(k)11:
nonresidential garages in § 110.9, § 130.0, § 130. 1, § 130.4, § 140.6, and § 141.0.
In a low-rise multifamily residential building where the total interior common area in a single building equals 20 percent or less of
§ 150.0(k)I2A:
the floor area, permanently installed lighting for the interior common areas in that building shall be high efficacy luminaires or
controlled by an occupant sensor.
In a low-rise multifamily residential building where the total interior common area in a single building equals more than 20
percent of the floor area, permanently installed lighting in that building shall:
i. Comply with the applicable requirements in § 110.9, § 130.0, § 130. 1, § 140.6 and § 141.0; and
§ 150.0(k) 1213:
ii. Lighting installed in corridors and stairwells shall be controlled by occupant sensors that reduce the lighting power in each
space by at least 50 percent. The occupant sensors shall be capable of turning the light fully On and Off from all designed paths of
ingress and egress.
Solar Ready Buildings:
Single family residences located in subdivisions with ten or more single family residences and where the application for a
§1 10.10(a)l:
tentative subdivision map for the residences has been deemed complete, by the enforcement agency, on or after January 1, 2014,
shall comply with the requirements of § 110.10 through § 110.10 e .
§ 110.10(a)2:
Low-rise multi -family buildings shall comply with the requirements of § 110.10(b) through § 110.10(d).
The solar zone shall have a minimum total area as described below. The solar zone shall comply with access, pathway, smoke
ventilation, and spacing requirements as specified in Title 24, Part 9 or other Parts of Title 24 or in any requirements adopted by a
local jurisdiction. The solar zone total area shall be comprised of areas that have no dimension less than 5 feet and are no less than
80 square feet each for buildings with roof areas less than or equal to 10,000 square feet or no less than 160 square feet each for
§ 110.10(b)1:
buildings with roof areas greater than 10,000 square feet.
For single family residences the solar zone shall be located on the roof or overhang of the building and have a total area no less
than 250 square feet. For low-rise multi -family buildings the solar zone shall be located on the roof or overhang of the building or
on the roof or overhang of another structure located within 250 feet of the building or on covered parking installed with the
building project and have a total area no less than 15 percent of the total roof area of the building excluding any skylight area.
§ 110.10(b)2:
All sections of the solar zone located on steep -sloped roofs shall be oriented between 110 degrees and 270 degrees of true north.
No obstructions, including but not limited to, vents, chimneys, architectural features, and roof mounted equipment, shall be
§ 110.10(b)3A:
located in the solar zone.
Any obstruction, located on the roof or any other part of the building that projects above a solar zone shall be located at least twice
§ 110.10(b)3B:
the distance, measured in the horizontal plane, of the height difference between the highest point of the obstruction and the
horizontal projection of the nearest point of the solar zone, measured in the vertical plane.
For areas of the roof designated as solar zone, the structural design loads for roof dead load and roof live load shall be clearly
§ 110.10(b)4:
indicated on the construction documents.
The construction documents shall indicate: a location for inverters and metering equipment and a pathway for routing of conduit
from the solar zone to the point of interconnection with the electrical service (for single family residences the point of
§ 110.10(c):
interconnection will be the main service panel); a pathway for routing of plumbing from the solar zone to the water -heating
system.
A copy of the construction documents or a comparable document indicating the information from § 110.10(b) through § 110.10(c)
§ I it0.10(d):
shall be provided to the occupant.
§ 110.10(e)I:
The main electrical service panel shall have a minimum busbar rating of 200 amps.
The main electrical service panel shall have a reserved space to allow for the installation of a double pole circuit breaker for a
§ 110.10(e)2:
future solar electric installation. The reserved space shall be: positioned at the opposite (load) end from the input feeder location or
main circuit location, and permanently marked as "For Future Solar Electric'.
HVAC SYSTEM HEATING AND COOLING LOADS SUMMARY
Project Name
Mrs. Lai Residence
Date
6/29/2015
System Name
HVAC
Floor Area
1,974
ENGINEERING CHECKS
SYSTEM LOAD
Number of Systems
1
COIL
CFM
Total Room Loads 1,016
Return Vented Lighting
Return Air Ducts
Return Fan
Ventilation 0
Supply Fan
Supply Air Ducts
TOTAL SYSTEM LOAD
COOLING
PEAK COIL HTG.
PEAK
Heating System
Sensible
Latent CFM
Sensible
Output per System 38,000
24,114
879 517
24,394
Total Output (Btuh) 38,000
0
Output Btuh/s ft) 19.3
1,094
1,355
Cooling System
0
0
Output per System 33,600
0
0 0
0
Total Output (Btuh) 33,600
0
879
0
Total Output (Tons) 2.8
1,094
1,355
Total Output (Btuh/s ft) 17.0
Total Output (s ft/Ton) 705.0
26,301
27,104
Air System
CFM per System
1,050
HVAC EQUIPMENT SELECTION
Airflow cfm
1,050
Carrier 58MVB40-14 CNP 38HD 3 T 31,985
387
38,000
Airflow (cfm/s ft)
0.53
Airflow (cfm/Ton)
375.0
Outside Air (%)
0,0%
Total Adjusted System Output 31,985 387
(Adjusted for Peak Design conditions)
TIME OF SYSTEM PEAK Aug 3 PM
38,000
Jan 1 AM
Outside Air (cfm/s ft) 0.00
Note: values above given at ARI conditions
HEATING SYSTEM PSYCHROMETRICS
(Airstream Temperatures at Time of Heating Peak)
28 OF
Outside Air
0 cfm
69 OF
69 OF 115 OF 115 OF
Heating Coil Supply Fan
1,050 cfm
114 OF
ROOM
70 OF
COOLING SYSTEM PSYCHROMETICS (Airstream Temperatures at Time of Cooling Peak)
88/68°F
Outside Air —4r 10
0 cfmCooling
79 / 63 OF
4 ;01
79/62°F 55/53°F 55/53°F
®-
Coil Supply Fan
1,050 cfm
41.2%
4 UA 4
56 / 54 OF
ROOM
78/ 62 OF
EnergyPro 6.5 by EnergySoft
User Number: 20692 Run Code: 2015-08-29708:08:32 ID: WHY15-0505
Page 5 of 5
A
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence
Calculation Description: Title 24 Analysis
Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 1 of 9
GENERAL INFORMATION
01
Project Name Mrs Lai Residence
Building Complies with Computer Performance
02
Calculation Description Title 24 Analysis
02
This building incorporates features that require field testing and/or verification by a certified HERS rater under the supervision of a CEC-approved HERS provider.
03
Project Location 10320 Moretti Dr.
04
City Cupertino
05
Standards Version Compliance 2015
06
Zip Code 95014
07
Compliance Manager Version BEMCmpMgr 2013-3c (710)
08
Climate Zone CZ4
09
Software Version EnergyPro 6.5
10
Building Type Single Family
11
Front Orientation (deg/Cardinal) 270
12
Project Scope Newly Constructed
13
Number of Dwelling Units 1
14
Total Cond. Floor Area (FTZ) 1974
15
Number of Zones 1
16
Slab Area (FTZ) 0
17
Number of Stories 1
18
Addition Cond. Floor Area N/A
19
Natural Gas Available Yes
20
Addition Slab Area (FTZ) N/A
21
Glazing Percentage (%) 16.5%
COMPLIANCE RESULTS
01
Building Complies with Computer Performance
02
This building incorporates features that require field testing and/or verification by a certified HERS rater under the supervision of a CEC-approved HERS provider.
03
This building incorporates one or more Special Features shown below
ENERGY USE SUMMARY
04
05
06
07
08
Energy Use
(kTDV/ft2-yr)
Standard
Design
Proposed
Design
Compliances
Margin ` \
Percent
Improvement
Space Heating
18.95
23.37
-4.42
-23.3%
Space Cooling
10.41
10.01
0.40
3.8%
IAQ Ventilation
1.17
1.17
0.0
0.0%
Water Heating
14.05
9.28
7
34.0%
Photovoltaic Offset
----
0.00
0.00
Compliance Energy Total
44.58
43.83
0.75
1.7%
Registration Number: 215-No175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF111-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD CF1 R -PRF -01
Project Name: Mrs Lai Residence Calculation Date/Time: 08:10, Mon, Jun 29, 2015 Page 2 of 9
Calculation Description: Title 24 Analysis Input File Name: 10320 Moretti rev 2T 1.7.xml
REQUIRED SPECIAL FEATURES
The following are features that must be installed as condition for meeting the modeled energy performance for this computer analysis.
• Cathedral Ceiling
• Window overhangs and/or fins
HERS FEATURE SUMMARY
The following is a summary of the features that must be field -verified by a certified HERS Rater as a condition for meeting the modeled energy performance for this computer analysis. Additional detail is
provided in the building components tables below.
Building -level Verifications:
• IAQ mechanical ventilation
Cooling System Verifications:
• Minimum Airflow
• Fan Efficacy Watts/CFM
HVAC Distribution System Verifications:
• Duct Sealing
Domestic Hot Water System Verifications:
• -- None --
ENERGY DESIGN RATING
This is the sum of the annual TDV energy consumption for energy use components included in the performance compliance approach for the Standard Design Building (Energy Budget) and the annual
TDV energy consumption for lighting and components not regulated by Title 24; Part 6 (such as domestic appliances and consumer electronics)and accounting for the annual TDV energy offset by an
on-site renewable energy system.
Reference Energy Use Energy Design Rating
Margin Percent Improvement
Total Energy (kTDV/f2-yr)' 90.02 89.27
0.75 0.8%
` includes calculated Appliances and Miscellaneous Energy Use (AMEU)
BUILDING - FEATURES INFORMATION
01
02
03
04
05
06
07
Project Name
Conditioned Floor Area (112)
Number of Dwelling
Units
Number of Bedrooms
Number of Zones
Number of Ventilation
Cooling Systems
Number of Water
Heating Systems
Mrs Lai Residence
1974
1
3
1
0
1
ZONE INFORMATION
01
02
03
04
05
06
07
Zone Name
Zone Type
HVAC System Name
Zone Floor Area
(ft2)
Avg. Ceiling
Height
Water Heating System 1
Water Heating System 2
New First Floor
Conditioned
HVAC1
1974
10
DHW Sys 1
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CFiR-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Calculation Description: Title 24 Analysis
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1R-PRF-01
Page 3 of 9
OPAQUE SURFACES
01
02
03
04
05
06
01
02
03
04
05
06
07
08
Name
Zone
Construction
Azimuth
Orientation
Gross Area (ft2)
Window & Door Area (ft)
Tilt (deg)
New Rear Wall
New First Floor
R-13 Wall
90
Back
441.7
104
90
New Left Wall
New First Floor
R-13 Wall
0
Left
580
93.6
90
New ront Wall
New First Floor
R-13 Wall
90
Back
441.7
128
90
New Right Wall
New First Floor
R-13 Wall
0
Left
580
120
90
New Roof 2
New First Floor
R-30 Roof Attic
1961.7
New First Floor 2
New First Floor
R-19 Floor Crawlspace
1974
OPAQUE SURFACES — Cathedral Ceilings
01
02
03
04
05
06
07
08
09
10
11
Name
Zone
Type
Orientatio
n
Area (ft)
Skylight Area
(ft2)
Roof Rise
(x in 12)
Roof
Pitch
Roof Tilt
(deg)
Roof
Reflectance
Roof
Emittance
Framing
Factor
New Roof
New First Floor
R-30 Roof Attic1
Left
12.4
12.3
4
0.33
18.43
0.1
0.85
0.07
ATTIC
01 02 03 04 05 06 07 08
Name Construction Type Roof Rise Roof Reflectance Roof Emittance Radiant Barrier Cool Roof
Attic New First Floor Attic RoofNew First Floor Ventilated 4 0.1 0.85 Yes No
Registration Number: 215-No175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Calculation Description: Title 24 Analysis
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 4 of 9
WINDOWS
01
02
03
04
Name
Side of Building
01
02
03
04
05
06
07
08
09
10
Name
Type
Surface (Orientation -Azimuth)
Width (ft)
Height (ft)
Multipli
er
Area
(ft)
U -factor
SHGC
Exterior Shading
Windows
Window
New Rear Wall (Back -90)
5.0
5.0
1.2
30.0
0.39
0.37
Insect Screen (default)
Window2
Window
New Rear Wall (Back -90)
5.0
5.0
0.4
10.0
0.39
0.37
Insect Screen (default)
Windowl 2
Window
New Left Wall (Left -0)
5.0
5.0
0.552
13.8
0.39
0.37
Insect Screen (default)
Window2 2
Window
New Left Wall (Left -0)
5.0
5.0
0.552
13.8
0.39
0.37
Insect Screen (default)
Window3
Window
New Left Wall (Left -0)
5.0
5.0
1.32
33.0
0.39
0.37
Insect Screen (default)
Window4
Window
New Left Wall (Left -0)
5.0
5.0
1.32
33.0
0.39
0.37
Insect Screen (default)
Windows 3
Window
New ront Wall (Back -90)
5.0
5.0
0.48
12.0
0.39
0.37 1
Insect Screen (default)
Window2 3
Window
New ront Wall (Back -90)
5.0
5.0
1.44
36.0
0.39
0.37
Insect Screen (default)
Window3 2
Window
New ront Wall (Back -90)
5.0
5.0
0.48
12.0
0.39
0.37
Insect Screen (default)
Windowl 4
Window
New Right Wall (Left -0)
5.0
5.0
0.48
12.0
0.39
0.37
Insect Screen (default)
Window2 4
Window
New Right Wall (Left -0)
5.0
5.0
0.48
12.0
0.39
0.37
Insect Screen (default)
Window3 3
Window
New Right Wall (Left -0)
5.0
5.0
0.6
15.0
0.39
0.37
Insect Screen (default)
Window4 2
Window
New Right Wall (Left -0)
5.0
5.0
0.6;
15.0
0.39
0.37
Insect Screen (default)
Window5
Window
New Right Wall (Left -0)
5.0
5.0
0.6
15.0
0.39
0.37
Insect Screen (default)
Window6
Window
New Right Wall (Left -0)
5.0
5.0 r
0.6
15.0
0.39
0.37
Insect Screen (default)
Windowl
Window
New Right Wall (Left -0)
5.0
5.0
0.24
6.0
0.39
0.37
Insect Screen (default)
Window8
Window
New Right Wall (Left -0)
5.0
5.0
0.24
6.0
0.39
0.37
Insect Screen (default)
Window9
Window
New Right Wall (Left -0)
5.0
5.0
0.48
12.0
0.39
0.37
Insect Screen (default)
Window10
Window
New Right Wall (Left -0)
5.0
5.0
0.48
12.0
0.39
0.37
Insect Screen (default)
Skylight
Skylight
New Roof (Left -0)
1
8.0
0.37
0.29
4 Suntunnels
Skylight
New Roof (Left -0)
1
4.3
0.37
0.29
DOORS
01
02
03
04
Name
Side of Building
Area (ft)
U -factor
Doorl
New Rear Wall
64.0
0.50
Door1 2
New ront Wall
20.0
0.50
Door2
New ront Wall
48.0
0.50
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Calculation Description: Title 24 Analysis
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 5of9
OVERHANGS AND FINS
01
02
03
04
05
06
07
08
09
10
11
12 13
14
Overhang
Left Fin
Right Fin
Window
Depth
Dist Up
Left
Extent
Right
Extent
Flap Ht.
Depth
Top Up
DistL
Bot Up
Depth
Top Up Dist R
Bot Up
Windows
0
0
0
0
0
0
0
0
0
0
0 0
0
Window2
0
0
0
0
0
0
0
0
0
0
0 0
0
Windowl2
0
0
0
0
0
0
0
0
0
0
0 0
0
Window2 2
0
0
0
0
0
0
0
0
0
0
0 0
0
Window3
0
0
0
0
0
0
0
0
0
0
0 0
0
Window4
0
0
0
0
0
0
0
0
0
0
0 0
0
Windowl3
0
0
0
0
0
0
0
0
0
0
0 0
0
Window2 3
0
0
0
0
0
0
0
0
0
0
0 0
0
Window3 2
0
0
0
0
0
0
0
0
0
0
0 0
0
Windowl4
0
0
0
0
0
0
0
0
0
0
0 0
0
Window2 4
0
0
0
0
0
0
0
0
0
0
0 0
0
Window3 3
0
0
0
0
0
0
0
0
0
0
0 0
0
Window4 2
0
0
0
0
0
0
0
0
0
0
0 0
0
Window5
0
0
0
0
0
0
0 --
0
0
0
0 0
0
Window6
0
0
0
0
0
0
0...
0
0
0
0 0
0
Window?
0
0
0
0
0
0
0
0
0
0
0 0
0
Window8
0
0
0
0
0
0
0
0
0
0
0 0
0
Window9
0
0
0
0
0
0
0
0
0
0
0 0
0
Windowl0
0
0
0
0
0
0
0
0
0
0
0 0
0
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Calculation Description: Title 24 Analysis Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 6 of 9
OPAQUE SURFACE CONSTRUCTIONS
01
02
03
04
05
06
07
Total Cavity
Winter Design
Construction Name
Surface Type
Construction Type
Framing
R -value
U -value
Assembly Layers
• Cavity/ Frame: no insul. /2x4 Top Chrd
• Roof Deck: Wood Siding/sheathing/decking
2x4 Top Chord of Roof Truss @ 24
• Tile Gap: present
Attic RoofNew First Floor
Attic Roofs
Wood Framed Ceiling
in. O.C.
none
0.400
• Roofing: 10 PSF (ROOMle)
• Floor Surface: Carpeted
Floors Over
• Floor Deck: Wood Siding/sheathing/decking
R-19 Floor Crawlspace
Crawlspace
Wood Framed Floor
2x6 @ 16 in. O.C.
R 19
0.049
• Cavity/ Frame: R -19/2x6
• Inside Finish: Gypsum Board
Ceilings (below
• Cavity/ Frame: R-9.1 /2x4
R-30 Roof Attic
attic)
Wood Framed Ceiling
2x4 @ 24 in. O.C.
R 30
0.032
• Over Floor Joists: R-20.9 insul.
• Inside Finish: Gypsum Board
• Cavity / Frame: R-30 /2x4
• Roof Deck: Wood Siding/sheathing/decking
• Tile Gap: present
R-30 Roof Attica
Cathedral Ceilings
Wood Framed Ceiling
2x4 @ 24 in. O.C.
R 30
0.039
• Roofing: 10 PSF (RoofTile)
• Inside Finish: Gypsum Board
• Cavity/ Frame: R -13/2x4
• Exterior Finish: Wood
R-13 Wall
Exterior Walls
Wood Framed Wall
2x4 @ 16 in. O.C.
R 13
0=095
Siding/sheathing/decking
BUILDING ENVELOPE - HERS VERIFICATION
01 02 03 04
Quality Insulation Installation (QII) Quality Installation of Spray Foam Insulation Building Envelope Air Leakage ACH @ 50 Pa
Not Required Not Required Not Required
WATER HEATING SYSTEMS
01
02 03 04 05 06
Name
System Type Distribution Type Water Heater Number of Heaters Solar Fraction (%)
DHW Sys 1 - 1/1
DHW Pipe Insulation, All Lines DHW Heater 1 1 .0%
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Calculation Description: Title 24 Analysis
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 7 of 9
WATER HEATERS
01
02
03
04
05
06
07
08
Name
Heater Element Type
Tank Type
Tank Volume
(gal)
Energy Factor or
Efficiency
Input Rating
Tank Exterior
Insulation
R -value
Standby Loss
(Fraction)
DHW Heater 1
Natural Gas
Small Instantaneous
0.2
0.84
199000-Btu/hr
0
0
WATER HEATING - HERS VERIFICATION
01
02
03
04
05
06
07
Name
Pipe Insulation
Parallel Piping
Compact Distribution
Point -of Use
Recirculation
Control
Central DHW
Distribution
DHW Sys 1 - 1/1
---
---
---
---
---
SPACE CONDITIONING SYSTEMS
01
02
03
04
05
06
SC Sys Name
System Type
Heating Unit Name
Cooling Unit Name
Fan Name
Distribution Name
Cooling Component 1:Heating Component 1:Air
Distribution System 1:HVAC Fan 1:1
Other Heating and Cooling
System
HeatingComponent 1
Cooling Component 1
HVAC Fan 1
Air Distribution System 1
HVAC - HEATING UNIT TYPES
01 02 03
Name Type Efficiency
Heating Component 1 CntrlFurnace - Fuel -fired central furnace 96.6 AFUE
HVAC - COOLING UNIT TYPES
01
02
03 04
05
06
07
Name
System Type
Efficiency
EER SEER
Zonally Controlled
Multi -speed
Compressor
HERS Verification
Cooling Component 1
SplitAirCond
11.3
13
Not Zonal
Single Speed
Cooling Component
1 -hers -cool
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence
Calculation Description: Title 24 Analysis
Calculation Date/Time: 08:10, Mon, Jun 29, 2015
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 8of9
HVAC COOLING - HERS VERIFICATION
01
02
03
04
05
06
Name
Verified Airflow
Airflow Target
Verified EER
Verified SEER
Verified Refrigerant
Charge
Cooling Component 1 -hers -cool
Required
350
Not Required
Not Required
Not Required
HVAC - DISTRIBUTION SYSTEMS
01 02 03
04 05
06
07
Name Type Duct Leakage
Insulation R -value Duct Location
Bypass Duct
HERS Verification
Air Distribution System 1 DuctsAttic Sealed and tested
6 Attic
None
Air Distribution System
1 -hers -dist
HVAC DISTRIBUTION - HERS VERIFICATION
01
02
03
04
05
06
07
08
Name
Duct Leakage
Verification
Duct Leakage
Target (%)
Verified Duct
Location
Verified Duct
Design
Buried
Ducts
Deeply Buried
Ducts
Low -leakage
Air Handler
Air Distribution System 1 -hers -dist
Required
6.0
Not Required
Not Required
Not Required
Not Required
---
HVAC-FAN SYSTEMS
01 02 03 04
Name Type Fan Power (Watts/CFM) HERS Verification
HVAC Fan 1 Single Speed PSC Furnace Fan 0.58 HVAC Fan 1 -hers -fan
HVAC FAN SYSTEMS - HERS VERIFICATION
01 02 03
Name Verified Fan Watt Draw Required Fan Efficiency (Watts/CFM)
HVAC Fan 1 -hers -fan Required 0.58
IAQ (Indoor Air Quality) FANS
01
02
03
04
05
06
Dwelling Unit
IAQ CFM
IAQ Watts/CFM
IAQ Fan Type
IAQ Recovery
Effectiveness(%)
HERS Verification
SFam IAQVentRpt
49.74
0.25
Default
0
Required
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54
CERTIFICATE OF COMPLIANCE - RESIDENTIAL PERFORMANCE COMPLIANCE METHOD
Project Name: Mrs Lai Residence Calculation DatefTime: 08:10, Mon, Jun 29, 2015
Calculation Description: Title 24 Analysis
Input File Name: 10320 Moretti rev 2T 1.7.xml
CF1 R -PRF -01
Page 9 of 9
DOCUMENTATION AUTHOR'S DECLARATION STATEMENT
1. 1 certify that this Certificate of Compliance documentation is accurate and complete.
Documentation Author Name:
Documentation Author Signature:
Aalele�
Jack Lin
Company:
Signature Date:
W H Y CONSTRUCTION
2015-06-29 08:30:17
Address:
CEA/HERS Certification Identification (If applicable):
6805 WESTMOOR WAY
City/State/Zip:
Phone:
SAN JOSE, CA 95129
(408) 218-0587
RESPONSIBLE PERSON'S DECLARATION STATEMENT
I certify the following under penalty of perjury, under the laws of the State of California:
1. I am eligible under Division 3 of the Business and Professions Code to accept responsibility for the building design identified on this Certificate of Compliance.
2. 1 certify that the energy features and performance specifications identified on this Certificate of Compliance conform to the requirements of Title 24, Part 1 and Part 6 of the California Code of
Regulations.
3. The building design features or system design features identified on this Certificate of Compliance are consistent with the information provided on other applicable compliance documents,
worksheets, calculations, plans and specifications submitted to the enforcement agency for approval with this building permit application.
Responsible Designer Name:
Responsible Designer Signature:'
Jack Lin
Company:
Date Signed:
W H Y CONSTRUCTION
2015-06-29 08:30:17
Address:
License:
6805 WESTMOOR WAY
CSLB #964820
City/State/Zip:
Phone:
SAN JOSE, CA 95129
(408) 218-0587
Digitally signed by Ca10ERTS. This digital signature is provided in order to secure the content of this registered document, and in noway implies Registration Provider responsibility for the accuracy of the
information.
Registration Number: 215-N0175546A-000000000-0000 Registration Date/Time: 2015-06-29 08:30:17 HERS Provider: CaICERTS inc.
CA Building Energy Efficiency Standards - 2013 Residential Compliance Report Version - CF1R-02272015-710 Report Generated at: 2015-06-29 08:10:54