Loading...
B-2017-0446CITY OF CUPERTINO BUILDING PERMIT BUILDING ADDRESS: CONTRACTOR: PERMIT NO: B-2017-0446 20697 FARGO DR CUPERTINO, CA 95014-1903 (326.33 03 1) C & D FREITAS CONSTRUCTION INC LOS GATOS, CA 95033 OWNER'S NAME: VISWANADHAM KRISHNA AND PHANNI K DATE ISSUED: 03/20/2017 OWNER'S PHONE: 408-353-1900 PHONE NO: (408) 421-1127 LICENSED CONTRACTOR'S DECLARATION BUILDING PERMIT INFO: License Class B Lic. #286517 Contractor C & D FREITAS CONSTRUCTION INC Date 01/31/2018 X BLDG —ELECT _ PLUMB T I hereby affirm that I am licensed under the provisions of Chapter 9 (commencing MECH X RESIDENIAL _ COMMERCIAL with Section 7000) of Division 3 of the Business & Professions Code and that my license is in full force and effect. JOB DESCRIPTION: BATHROOM REMODEL (210 S.F); RAISE FLOOR IN LIVING ROOM I hereby affirm under penalty of perjury one of the following two declarations: 711 1. I have and will maintain a certificate of consent to self-insure for Worker's Compensation, as provided for by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. z. , I have and will maintain Worker's Compensation Insurance, as provided for by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. Sq. Ft Floor Area: Valuation: $32000.00 APPLICANT CERTIFICATION I certify that I have read this application and state that the above information is correct. I agree to comply with all city and county ordinances "N Number: Occupancy Type: and state laws relating to building construction, and hereby authorize 32633031 representatives of this city to enter upon the above mentioned property for inspection purposes. (We) agree to save indemnify and keep harmless the City, of Cupertino against liabilities, judgments, costs, and expenses which PERMIT EXPIRES IF WORK IS NOT STARTED may accrue ainst said Ci inconsequence of the granting of this permit. WITHIN 180 DAYS OF PERMIT ISSUANCE OR Additio y, the applican derstands and will comply with all non-point soupa regulati er t Cup e trto unicipal Code, Section 9.18. 180 DAYS FROM LAST CALLED INSPECTION. ' Signature Date 3/20/2017 Issued by: Abby Aygnde Date: 03/20/2017 OWNER-B Tti D •R DECLARATION I hereby affirm that I am exempt from the Contractor's License Law for one of the RF.-ROOFS: following two reasons: All roofs shall be inspected prior to any roofing material being installed. If a roof is 1. I, as owner of the property, or my employees with wages as their sole installed without first obtaining an inspection, I agree to remove all new materials for compensation, will do the work, and the structure is not intended or offered for inspection. sale (Sec.7044, Business & Professions Code) 2. I, as owner of the property, am exclusively contracting with licensed Signature of Applicant: contractors to construct the project (Sec.7044, Business & Professions Code). Date: 3/20/2017 I hereby affirm under penalty of perjury one of the following three declarations: ALL ROOF COVERINGS TO BE CLASS "A" OR BETTER 1. I have and will maintain a Certificate of Consent to self-insure for Worker's Compensation, as provided for by Section 3700 of the Labor Code, for the performance of the work for which this permit is issued. HAZARDOUS MATERIALS DISCLOSURE 2. I have and will maintain Worker's Compensation Insurance, as provided for by I have read the hazardous materials requirements under Chapter 6.95 of the Section 3700 of the Labor Code, for the performance of the work for which this California Health & Safety Code, Sections 25505, 25533, and 25534. I will maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and the permit is issued. Health & Safety Code, Section 25532(a) should I store or handle hazardous s. I certify that in the performance of the work for which this permit is issued, I shall not employ any person any manner so as to become subject to the material. Additionally, should I use equipment or devices which emit hazardous air contaminants as defined.byl t e ay Area Air Q 't}IMana t District I Worker's Compensation laws of California. If, after making this certificate of will maintain compliance it C rtino Mu ipale; Chapter : 2 and exemption, I become subject to the Worker's Compensation provisions of the the Health & afety d ctions 25505, 3, an 25534. Labor Code, I must forthwith comply with such provisions or this permit shall be deemed revoked. ,- Owner or authorized agent: – APPLICANT CERTIFICATION ' Date: 312912417 1 certify that I have read this application and state that the above information is CONSTRUCTION LENDING AGENCY correct. I agree to comply with all city and county ordinances and state laws I hereby affirm that there is a construction lending agency for the performance relating to building construction, and hereby authorize representatives of this city of work's for which this 1permit is issued (Sec. 3097, Civ C.) to enter upon the above mentioned property for inspection purposes. (We) agree Lender's Name to save indemnify and keep harmless the City of Cupertino against liabilities, judgments, costs, and expenses which may accrue against said City in Lender's Address consequence of the granting of this permit. Additionally, the applicant understands 11 and will comply with all non-point source regulations per the Cupertino Municipal ARCHITECT'S DE blit records. Code, Section 9.18. I understand my plans shall be used as public records. Licensed Signature Date 3/20/2017 Professional AdCOMMUNITY DEVELOPMENT DEPARTMENT • BUILDING DIVISION 10300 TORRE AVENUE • CUP.ERTINO, CA 95014-3255 Ct�i `EF�itNO TV(4018)1777-3228 • FAX (408) 777 (@ 3333 • buildingcupertino.org FWC'n— NCTRTTC`TT0KT I I ATl1YrrTC)XT n Aa rnDAran_.Ti'1,a n �c�rcTnrr ir��ccnn>✓rnnrn_r�,nr n PROJECT ADDRESS � � APN # `r� � �2 r 'a 15 0 AIA V2 %0 Y( j �T ? I / r ,r, "� OWNER NAME , PHONE 3s 3 --c' E-MAIL C cc STREET ADDRESS 2_0Gc ,? ) CITY, STATE, ZIP FAX CONTACT NAME PHONE. ; 4p –I ! d, 7 E-MAIL t �" r � � 0 % g `r -C STREET ADDRESS CITY, STA' E, ZIP 0470:51 q5® ° FAX, /\ El OWNER I-]OwNER-BUH,DER. ❑ OWNER AGENT CONTRACTOR El CONTRACTOR AGENT El ARCHITECT ❑ ENGINEER El DEVELOPER ❑ TENANT CONTRACTOR NAMEms a LICENSE Etq '05LICEN , 7 YPE BUS. LIC # COMPANY NAMEL 1 L e is E-MAIL FAX �C STREET ADDRESS 2-'2 He CITY, TATE, ZIP PHO ARCHITECT/EN�INEE A& - tce t\J6Z LICENSE NUMBER r CTL BUS. LIC # COMPANY NAMES //�� �� E-MAIL EkIX STREET ADDRESS �` *M CIATY, STATE, ZIP , � IJBSCRIPTION O'FWORIC ----�� SPH EXISTING USE PROPOSED USE CONSTR TYPE #STORIES USE TYPE OCC. SQ.FT. VALUATION ($} EXISTG NEW FLOOR DEMO TOTAL AREA AREA AREA NET AREA BATHROOM 1 REMODEL fit A o KITCHEN REMODEL AREA OTHER REMODEL AREA — PORCH AREA DECK AREA TOTAL DECK/PORCH AREA GARAGE AREA: ElDETACH I ❑ AT CH # DWELLING UNITS: IS A SECOND UNIT ❑ YES SECOND STORY ❑ YES BEING ADDED? ❑ NO ADDITION? ❑ NO PRE -APPLICATION ❑ YES IF YES, PROVIDE COPY OF PLANNING APPL # Fl NO PLANNING APPROVAL LETTER IS THE BLDG AN ❑ YES EICHLER HOME? []NO RECEIVED 73Y' OTAL VALUATION: ) 060 By my signature below, I certify to each e following: I am er or authorized agent to act on the property owner's behalf. I have read this application and the information I pr d i rrect. I e D scri ., f Work and verify it is accurate. I agree to comply with all applicable local ordinances and state laws rela ' to bu' ing s ction. a o - e ep se Ives f Cupertino to enter the abovetidentifieiproperty for inspection purposes. Date: Signature of Applicant/Agent: SUPPLEMENTAL INFORMATION REQUIRED PLAN CHECK tPE ROUTING SLIP ❑ OVER-THE-COUNTER ❑ BUILDING PLAN REVIEW _ New SFD or Multifamily dwellings: Apply for demolition permit for existing building(s). Demolition permit is required prior to issuance of building permit for new building. ❑ EXPRESS ❑ PLANNING PLAN REVIEW Commercial Bldgs: Provide a completed Hazardous Materials Disclosure ❑ STANDARD © PUBLIC WORKS form if any Hazardous Materials are being used as part of this project. ❑ LARGE ❑ FIRE DEPT _ Copy of Planning Approval Letter or Meeting with Planning prior to ❑ MAJOR ❑ SANITARY SEWER DISTRICT submittal Of Building Permit application. ❑ ENVIRONMENTAL HEALTH BldgApp_2011.doc revised 06121/11 ICDM 6. N. W. E. FS -� = 85.0 PROPERTY LINES +I +I NO 51TE GRADING OR r MODIFICATION5 ARE PROP05ED N I I I I I I I I 2ND STORY WALL OUTLINES I � I I I I I I I (E) 2 STORY RE5IDENCE AREA OF❑ 2ND STORY- F_ O REMODEL I 12'-0" ± O of o I I I I I I I 12'-10" ± AREA OF I 15T STORY I (E) 3 CAR GARAGE REMODEL L (E) 200A MAIN (E) 6' FENCE ELECTRIC PANEL W/ METER PORCH - (E) GAS METER 2016 CRC R I FABLE 2304.9.1 i CONNECTION FASTENING to t LOCATION 1. JOIST TO SILL OR GIRDER 3-8d COMMON (2 1/2" X 0.131") TOENAIL 13. NAIL5 SPACED AT 6" ON CENTER AT EDGES, 12" AT INTERMEDIATE 5UPORT5 EXCEPT 6" 3-3" X 0,131" NAILS 3- 3" 14 GAGE STAPLES AT 5UPPORT 5TRUCTURAL PANEL AND PARTICLEBOARD DIAPHRAM5 AND 5HEAR WALLS. 2, BRIDGING TO JOIST 2-8d COMMON (2 1/2" X 0.131") TOENAIL EACH END MODIFICATIONS ARE 2-3" X 0.131" NAILS _ ", it 2- 3" 14 GAGE STAPLES I PROP05ED I 3. 1"X6" SUBFLOOR OR LESS TO EACH JOIST 2-8d COMMON (2 1/2" X 0.131") FACE NAIL 4. WIDER THAN 1"X6" SUBFLOOR TO EA JOIST 3-8d COMMON (2 1/2" X 0.131") FACE NAIL 5. 2" SUBFLOOR TO JOIST OR GIRDER 2-16d COMMON (3 1/2" X 0.162") BLIND & FACE NAIL 6. SOLE PLATE TO JOIST OR BLKG. 16d (3 1/2" X 0.135") ® 16" OC. TYPICAL FACE NAIL E. DEFORMED SHANK (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.148"). F. CORRO51ON-RE5I5TANT SIDING (6d-2" X 0.113"; &1-2 1 /2" x 0.131 "; 1 Od-3" X 0.146") OR CASING (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.148") NAIL. G. FASTENERS SPACED 3 INCHES ON CENTERAT EXTERIOR EDGES ADND 6 INCHES ON CENTERAT INTERMEDIATE 5UPPORT5, WHEN USED A5 STRUCTURAL SHEATHING. 3" X 0.131" NAILS 0 8" OC. 3" 14 GAGE STAPLES @ 12" OC. SOLE PLATE TO JOIST OR BLKG. 3"- 16d (3 1/2" X 0.135") 0 16" BRACED WALL PANELS ® BRACED WALL PANEL 4- 3" X 0.131" NAILS ® 16" for over 45 years 4- 3" 14 GAGE STAPLES PER 16" Residence3490 SF± No Change to Existing Residence(3490 g 7. TOP PLATE TO STUD 2-16d COMMON (3 1/2" X 0.162") END NAIL co 3-3" X 0.131" NAILS Description DATE 3- 3" 14 GAGE STAPLES I I � 8. STUD TO SOLE PLATE 4-8d COMMON (2 1/2" X 0.131") TOENAIL 4-3" X 0.131" NAILS 3- 3" 14 GAGE STAPLES L1urlIbar Dr 2-16d COMMON (3 1/2" X 0.162") END NAIL 23620 Morrell Road 3-3" X 0.131" NAILS Proposed Remodel Area 500.0 S.F. 3- 3" 14 GAGE STAPLES 9. DOUBLE STUDS 16d (3 1/2" X 0.135") ® 16" FACE NAL WOOD 5TRUCTURAL PANELS. 3" X 0.131" NAILS ® 12" OC. 3" 14 GAGE STAPLES ® 8" OC. 0 10. DOUBLE TOP PLATES 16d (3 1/2" X 0.135") @ 16" OC. TYPICAL FACE NAIL 3" X 0.131" NAILS ® 12" OC. %'�•Ihar CI 3" 14 GAGE STAPLES 0 12" OC. DOUBLE TOP PLATES 8-16d COMMON (3 1/2" X 0.162") LAP SPLICE 12-3" X 0.131" NAILS 12-3" 14 GAGE STAPLES License #6286517 11. BLOCKING BET. JOISTS OR 3-8d COMMON (2 1/2" X 0.131") TOENAIL RAFTERS TO TOP PLATE. 3-3" X 0.131" NAILS Occupancy Group R3/U 3- 3" 14 GAGE STAPLES 12. RIM JOIST 1'0 TOP PLATE 8d (2 1/2" X 0.131") 0 6" OC, TOENAIL ?20697 3" X 0.131" NAIL ® 6" OC. without consent is prohibited and infringement will be subject to legal action 3" 14 GAGE STAPLE 0 6" OC. 13. TOP PLATES, LAPS AND INTERSECTION 2-16d COMMON (3 1/2" X 0.162") FACE NAIL s 3-3" X 0.131" NAILS 3- 3"14 GAGE STAPLES 14. CONTINUOUS HEADER, TWO PIECES 16d COMMON (3 1/2" X 0.162") 16" OC. ALONG EDGE - 15. CEILING JOIST TO PLATE 3-8d COMMON (2 1/2" X 0.131") TOENAIL 5-3" X 0.131" NAILS FA5TENER SCHEDULE 2016 Title 24 5- 3" 14 GAGE STAPLES 16, CONTINUOUS HEADER TO STUD 4-8d COMMON (2 1/2" X 0.131") TOENAIL 17. CEILING JOIST, LAPS OVER PARTITIONS 3-16d COMMON (3 1/2" X 0.162") MIN. FACE NAIL TABLE 2308.10.4.1 4-3" X 0.131" NAILS • CONTRACTOR5 AND ALL SU13CONTRACTOR5 5HALL VERIFY ALL DIMEN51ON5, GRADE[) AND 4- 3" 14 GAGE STAPLES 3 1 DC 18. CEILING JOIST TO PARALLEL RAFTERS 3-16d COMMON (3 1/2" X 0.162") MIN. FACE NAIL TABLE 2308.10.4.1 b FARGODIVE GONDITION5 BEFORE PROCEEDING WITH PROJECT. IFABIDDERFIND5DE5CREPANCIE5ORAMBIGUITIE5INDRAWING5,OR15INDOU13TA5T0 THEIR MEANING, I3IDDER5HALL NOTIFYTHE ARCHITECTAND REQUE5TA CLARIFICATION. 4-3" X 0.131" NAILS Developrnent Center DATE: 03/06/17 4- 3" 14 GAGE STAPLES 19. RAFTER TO PLATE 3-8d COMMON (2 1/2" X 0.131") TOENAIL AFTER EXECUTION OF THE CONTRACT, NO CONDI5ERATION WILL 13E GIVEN TO ANY CLAIM OF 3-3" X 0.131" NAILS 3- 3" 14 GAGE STAPLES Krishina & Phanni 20. BUILT-UP CORNER STUDS 16d COMMON (3 1/2" X 0.162") 24" OC. SCALE: 1/4" - V-0" 3" X 0.131" NAILS 16" OC. • CONTRACTOR 5HALL VERIFY EX151TING STRUCTURE, PROVIDE TEMORARY 5UPPORT5 FOR 3" 14 GAGE STAPLES 16" OC. I I (E) 6' FENCE ❑ ❑ I A. COMMON OR BOX NAIL5 ARE PERMITTED TO 13E U5ED EXCEPT WHERE OTHERWISE 5TATED. Sport C & D Freitas 13. NAIL5 SPACED AT 6" ON CENTER AT EDGES, 12" AT INTERMEDIATE 5UPORT5 EXCEPT 6" NO 51TE GRADING OR I AT 5UPPORT 5TRUCTURAL PANEL AND PARTICLEBOARD DIAPHRAM5 AND 5HEAR WALLS. DRAWING INDEX Construction, Inc. MODIFICATIONS ARE 119 _ ", it I PROP05ED I BOX OR CASING. I Dre�jilaai Dr Gr unleaf Dr Project Address 20697 FARGO DRIVE Fine Quality o E. DEFORMED SHANK (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.148"). F. CORRO51ON-RE5I5TANT SIDING (6d-2" X 0.113"; &1-2 1 /2" x 0.131 "; 1 Od-3" X 0.146") OR CASING (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.148") NAIL. G. FASTENERS SPACED 3 INCHES ON CENTERAT EXTERIOR EDGES ADND 6 INCHES ON CENTERAT INTERMEDIATE 5UPPORT5, WHEN USED A5 STRUCTURAL SHEATHING. Assessors Parcel No. 326-033-031 Zoning R-1-10 Lot Area 9,350.0 S. F. Home Building r� Building Floor Area Gr�vr11�0f f�r Marl for over 45 years H. CORROSION-RE515TANTROOFING NAIL5 7/16INCH DIAMETER HEAD AND 1 1/21NCH LENGTH FOR 1/2 INCH SHEATHING AND 1 3/4 INCH LENGTH FOR 25/32 INCH SHEATHING. Residence3490 SF± No Change to Existing Residence(3490 g rD -- TJ co # Description DATE I I � I. CORROSION RE515TANT5TAPLE5 WITH NOMINAL 7/16 INCH CROWN AND 1 1/8INCH LENGTH FOR 1/2 INCH 5HEATHING AND 1 1/2 INCH LENGTH FOR 25/32 INCH 5HEATHING. PANEL SUPPORTS AT 16 INCHES (20 INCHE5) IF STRENGHT AXIS IN THE LONG DIRECTION Garage (3 car) No Change to Existing b L1urlIbar Dr ? 23620 Morrell Road OF THE PANEL, UNLE55 OTHERWISE MARKED). J. CA51NG (1 1/2" X 0.080") OR FIN15H (1 1/2" X 0.072") ARE THE MINIMUM REQUIRED FOR Proposed Remodel Area 500.0 S.F. 0} Los Gatos, CA 95033 WOOD 5TRUCTURAL PANELS. 0 Phone (408) 353-1900 Fax (408) 353-2209 %'�•Ihar CI K. PANEL 5UPPORT5 AT 24 INCHE5. CA51NG OR FIN15H NAILS 5PACED 6 INCHE5 ON PANEL www.freitasconstruction.com EDGES, 121NCHE5ATINTERMEDIATE5UPPORT5. Floor Area Ratio No Change to Existing L. FOR ROOF 5HEATHING APPLICATION5, Sd NAILS (2 1/2" X 0.1 13") ARE THE MINIMUM License #6286517 REQUIRED FOR WOOD STRUCTURAL PANEL5. Occupancy Group R3/U This drawing, file and the design shown is the property of the designer. The reproduction, copy or use of this drawing or any portion thereof M. STAPLES SHALL HAVE MINIMUM CROWN WIDTH OF 7/16 INCH. N. FOR ROOF 5HEATHING APPLICATION5, FA5TENER5 5PACED 4 INCHE5 ON CENTER AT Construction Type VB, Automatic -Fire Sprinklered ?20697 without consent is prohibited and infringement will be subject to legal action rrc Dr Fargo drive s SHEET TITLE: o o co INCHE5 AT INTERMEDIATE 5UPPORT5 FOR ROOF 5HEATHING. P. FA5TENER5 5PACED 4 INCHE5 ON CENTER AT EDGES, 8 INCHE5 AT INTERMEDIATE SUPPORTS. 2016 C EC 2016 CPC SITE PLAN FA5TENER SCHEDULE 2016 Title 24 Fgfgo fir 2016 CGBSC • CONTRACTOR5 AND ALL SU13CONTRACTOR5 5HALL VERIFY ALL DIMEN51ON5, GRADE[) AND Jurisdiction City of of Cupertino 3 1 DC Kinderland Child L.." Chinese Church In ChfW OWNER: b FARGODIVE GONDITION5 BEFORE PROCEEDING WITH PROJECT. IFABIDDERFIND5DE5CREPANCIE5ORAMBIGUITIE5INDRAWING5,OR15INDOU13TA5T0 THEIR MEANING, I3IDDER5HALL NOTIFYTHE ARCHITECTAND REQUE5TA CLARIFICATION. < 0- Developrnent Center DATE: 03/06/17 AFTER EXECUTION OF THE CONTRACT, NO CONDI5ERATION WILL 13E GIVEN TO ANY CLAIM OF Hricr ray Krishina & Phanni MISUNDERSTANDING OF THE CONTRACTDOCUMENT5. domestic hot water systems. SCALE: 1/4" - V-0" Jinn€) -d D- • CONTRACTOR 5HALL VERIFY EX151TING STRUCTURE, PROVIDE TEMORARY 5UPPORT5 FOR Viswanadham Ducat! North Ar17eric�l 20697 Fargo Drive • VERIFY ALL NEW FIN15HE5 BEFORE PROCEEDING. ALL COLOR5, ETC. TO 13E 5ELECTED DY Cupertino, CA OWNER. • ALL NEW CADINET5 TO 13E DESIGNED 13Y OTHER5. STYLE AND FIN15HE5 5ELECTED BY SHEET: OWNERS. 0 4' 8' 12' 16' 32' ALL NEW PLUMBING FIXTURE5, ACCE55ORIE5 AND ELECTRICAL FIXTURE5 5ELECTED DY OWNERS. CUPERTINO A- 1 r• .i.r r.i 51TE PLAN le sCa1/Off - if -off Building Departm GENERAL NOTES PROJECT DATA VICINITY MAP SHEET N0. OWNERS A -1-A4-4- 51TE PLAN & PROJECT DATA KRISHNA & PHANNI V15WANADHAM A-2 -0 9 15T 5TORY REMODEL 20697 FARGO DRIVE CUPERTINO, CA 95014 A-3 2ND STORY REMODEL PLAN MM MANDATORY MEA5URE5 ARCHITECT LOU15 R DORCICH, ARCHITECT P.O. BOX 7306 5AN J05E, CA 95150 COMMUNITY DEVELOPME EPARTMENT 831/430-97482's BUILDING DIVISION - ERTINO APPRO D CONTRACTOR This set of plans and specifications MUS kept at the job during construction. It is unlawful to m any changes or INC.site C&DFREITASCON5TRUCTION,C alterations on same, or to deviate therefro ithout approval 2 3620 MORRELL ROAD from the Building Officia The stamping of this plan and specifcatio HALL NOT be L05 GATO5, CA 95033 held to permit or to be an approval of th olation of any 406/353-900 provision of any City Ordinance or to Law. BY Abby A ende DATE 03/20/17 PERMIT NO B-2017-0446 I I (E) 6' FENCE ❑ ❑ I A. COMMON OR BOX NAIL5 ARE PERMITTED TO 13E U5ED EXCEPT WHERE OTHERWISE 5TATED. 13. NAIL5 SPACED AT 6" ON CENTER AT EDGES, 12" AT INTERMEDIATE 5UPORT5 EXCEPT 6" NO 51TE GRADING OR I AT 5UPPORT 5TRUCTURAL PANEL AND PARTICLEBOARD DIAPHRAM5 AND 5HEAR WALLS. DRAWING INDEX PROJECT R05TER MODIFICATIONS ARE REFER TO 5ECTION 2305. NAIL5 FOR WALLS 5HEATHING ARE PERMITTED TO 13E COMMON, I PROP05ED I BOX OR CASING. I C. COMMON OR DEFORMED SHANK (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.146"). Project Address 20697 FARGO DRIVE D. COMMON (6d-2" X 0.113"; Sd-2 1 /2" x 0.131 "; 10d-3" X 0.148"). (E) DRIVEWAY o , N I E. DEFORMED SHANK (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.148"). F. CORRO51ON-RE5I5TANT SIDING (6d-2" X 0.113"; &1-2 1 /2" x 0.131 "; 1 Od-3" X 0.146") OR CASING (6d-2" X 0.1 13"; Sd-2 1 /2" x 0.131 "; 1 Od-3" X 0.148") NAIL. G. FASTENERS SPACED 3 INCHES ON CENTERAT EXTERIOR EDGES ADND 6 INCHES ON CENTERAT INTERMEDIATE 5UPPORT5, WHEN USED A5 STRUCTURAL SHEATHING. Assessors Parcel No. 326-033-031 Zoning R-1-10 Lot Area 9,350.0 S. F. 5PACEING SHALL BE 6 INCHES ON CENTER ON THE EDGES AND 12 INCHE5 ON CENTERAT INTERMEDIATE 5UPPORT5 FOR NON5TRUCTURAL APPLICATION5. Building Floor Area REVISIONS: I H. CORROSION-RE515TANTROOFING NAIL5 7/16INCH DIAMETER HEAD AND 1 1/21NCH LENGTH FOR 1/2 INCH SHEATHING AND 1 3/4 INCH LENGTH FOR 25/32 INCH SHEATHING. Residence3490 SF± No Change to Existing Residence(3490 g # Description DATE I I � I. CORROSION RE515TANT5TAPLE5 WITH NOMINAL 7/16 INCH CROWN AND 1 1/8INCH LENGTH FOR 1/2 INCH 5HEATHING AND 1 1/2 INCH LENGTH FOR 25/32 INCH 5HEATHING. PANEL SUPPORTS AT 16 INCHES (20 INCHE5) IF STRENGHT AXIS IN THE LONG DIRECTION Garage (3 car) No Change to Existing - - - - - - - - - - - - - - - - - - - - - - - 85.0 OF THE PANEL, UNLE55 OTHERWISE MARKED). J. CA51NG (1 1/2" X 0.080") OR FIN15H (1 1/2" X 0.072") ARE THE MINIMUM REQUIRED FOR Proposed Remodel Area 500.0 S.F. WOOD 5TRUCTURAL PANELS. K. PANEL 5UPPORT5 AT 24 INCHE5. CA51NG OR FIN15H NAILS 5PACED 6 INCHE5 ON PANEL EDGES, 121NCHE5ATINTERMEDIATE5UPPORT5. Floor Area Ratio No Change to Existing L. FOR ROOF 5HEATHING APPLICATION5, Sd NAILS (2 1/2" X 0.1 13") ARE THE MINIMUM REQUIRED FOR WOOD STRUCTURAL PANEL5. Occupancy Group R3/U M. STAPLES SHALL HAVE MINIMUM CROWN WIDTH OF 7/16 INCH. N. FOR ROOF 5HEATHING APPLICATION5, FA5TENER5 5PACED 4 INCHE5 ON CENTER AT Construction Type VB, Automatic -Fire Sprinklered EDGES,8INCHE5 ATINTERMEDIATE 5UPPORT5. 0. FASTENERS SPACED 4 INCHES ON CENTER AT EDGES, 8 INCHE5 AT INTERMEDIATE 5UPPORT5FOR 5U6FLOORAND WALL 5HEATHING AND 3INCHE5 ONCENTER ATEDGES, 6 Code References 2016 CRC 2016 CMC SHEET TITLE: o o co INCHE5 AT INTERMEDIATE 5UPPORT5 FOR ROOF 5HEATHING. P. FA5TENER5 5PACED 4 INCHE5 ON CENTER AT EDGES, 8 INCHE5 AT INTERMEDIATE SUPPORTS. 2016 C EC 2016 CPC SITE PLAN FA5TENER SCHEDULE 2016 Title 24 2016 CGBSC • CONTRACTOR5 AND ALL SU13CONTRACTOR5 5HALL VERIFY ALL DIMEN51ON5, GRADE[) AND Jurisdiction City of of Cupertino b FARGODIVE GONDITION5 BEFORE PROCEEDING WITH PROJECT. IFABIDDERFIND5DE5CREPANCIE5ORAMBIGUITIE5INDRAWING5,OR15INDOU13TA5T0 THEIR MEANING, I3IDDER5HALL NOTIFYTHE ARCHITECTAND REQUE5TA CLARIFICATION. Project Description Remodel Living Room &Master Bath of 2 story residence. No change to exterior envelope or HVAC, DATE: 03/06/17 AFTER EXECUTION OF THE CONTRACT, NO CONDI5ERATION WILL 13E GIVEN TO ANY CLAIM OF MISUNDERSTANDING OF THE CONTRACTDOCUMENT5. domestic hot water systems. SCALE: 1/4" - V-0" • CONTRACTOR 5HALL VERIFY EX151TING STRUCTURE, PROVIDE TEMORARY 5UPPORT5 FOR FLOOR, ETC. A5 NEEDED PRIOR TO REMOVAL OF ANY WALL, POST OR BEAM. • VERIFY ALL NEW FIN15HE5 BEFORE PROCEEDING. ALL COLOR5, ETC. TO 13E 5ELECTED DY OWNER. • ALL NEW CADINET5 TO 13E DESIGNED 13Y OTHER5. STYLE AND FIN15HE5 5ELECTED BY SHEET: OWNERS. 0 4' 8' 12' 16' 32' ALL NEW PLUMBING FIXTURE5, ACCE55ORIE5 AND ELECTRICAL FIXTURE5 5ELECTED DY OWNERS. CUPERTINO A- 1 51TE PLAN le sCa1/Off - if -off Building Departm GENERAL NOTES PROJECT DATA Reviewed By:Arnold Horn Date: 03/20/17 Reviewed By:Arnold Horn Date: 03/20/17 C & D Freitas (E) WALL - REMOVE (E) (E) WALL - REMOVE (E) N. Construction, Inc. DRYWALL @ (N) RAISED DRYWALL @ (N) RAISED FLOOR FLOOR 3/4" OSB 5UI3FLOOR 3/4" OSB SUBFLOOR W. E. Fine Quality (E) SUBFLOOR (E) SUBFLOOR 0/ F.J. W/ 1 Od @ 1 O/6 0/ 0/ F.J. W/ 10d @ 10/6 0/ (ZD 17 Home Building 7\11,'E.N. 2X6 F.J. @ 16" O.C. E N 2X6 F.J. @ 16" O.C. (N) 2X6 BLOCKING -Hs. � (E) SUBFLOOR for over 45 years 23620 Morrell Road -H r (E) 5UI3FLOOR O/ F.J. Los Gatos, CA 95033 0/ F.J. Phone (408) 353-1900 Fax (408) 353-2209 (N) 1 X6 SLEEPER (N) 1 X6 SLEEPER www.freitasconstruction.com @ PERIMETER License #13286517 (E) FOOTING (E) FOOTING This drawing, file and the design shown is the property of the designer. The reproduction, copy or use of this drawing or any portion thereof without consent is prohibited and infringement will be subject to legal WHERE OCCURS WHERE OCCURS FAMILY (ZOOM / NOOK / KITCHEN FAMILY ROOM / NOOK / KITCHEN action Krish i n a & P han n i RA15ED FLOOR SCALE: 1 "-1'-0" RA15ED FLOOR SCALE: 1 "-1'-O" 2 Viswanadham 20697 Fargo Drive Cupertino, CA (E) CEILING JOISTS OR BLOCKING (E) (N) 5IMP50N STC CLIP — — — — — (E) TO C.J. OR BLOCKING (N) 2X4 STUDS @ 16" O.C. I I v I I PORCH I I I I PORCH o 0 2-2X4 TOP PLATES (N) 2X4 SOLE PLATE W/ 16d 16" O.C. El (N) 1 /2" GYP. BD. @ (N) t- - (E) SUBFLOOR o (N) 2X4 STUDS @ 16" O.C. r' o I DINING ROOM 21 _ DINING ROOM 0 1 N (nl N (N) 1 /2" GYP. 13D.1 z � 1 REFINISH (E) N 01 1 I HARDWOOD FLOOR w cn 1 �I �I L _ I I I I L ❑ - - - - - - ❑ L I I I I - ❑ - - - - ❑ NON-BEARING WALL SCALE: 1 " " -1'-0 3 RAISE ALL (E) LIGHT SWITCHES, (E) PHONE OUTLETS, ELEC. TRANSITION WOOD OUTLETS AT LIVING ROOM 2 / STRIP TO FOYER FLOOR LU (N) STEP DOWN (±7") A2 ,f (N) HARDWOOD FLOOR AT LIVING ROOM W/ ER. TILE AS ELEC D ❑ NOTE: 1 1 (N) DA5EDOARD5 13YOWNERS STEP r - = 1 X6 SLEE ER - - FIELD VERIFY DIRECTION OF (E) FLOORJOIST5 Qq 1 1 LIVING ROOM I `� 1 LIVING ROOM PRIOR TO START OF WORK FOYERN 1 1 1 7.5' CEILING HT. 12 -INCH CLEAR MIN. PER FOYER N 1 18' CEILING HT. �Jo E715C 5 D.o w 1 GARAGE 9 (E) TABLE R1001.1 OF 2016 CRC, ITEM (b), TYPICAL GARAGE o fl. N) 2 D O (E) fl -100y, 0 RAISE (E) LIVING ROOM FLOOR TO AT EACH SIDE 7" STEP DN. TO LIVING ROOM �1 PA (N) 3/4" OSB T&G MATCH FOYER /DINING ROOM A 1 X6 5LEE ER 5UBFLOORING W/ I STAGGERED PATTERN- NAIL W/ 1 Od @ 1 O/6 EDGE OF (N) 7" STEP DOWN 2'-0" L VIN ROCM ' (E) 2'-0" RAISE (E) FLOOR MOUNTED � HEAT REG. WITH NEW FLUSH I EDGE OF (E) MAX. v MOUNTED GRILLES 1 RAISED A2 FLOOR REPAINT AFFECTED WALL � 10'-6" WALL HEIGHT TO CEILING REVISIONS: 1X6 SLEE ER - __ L — — —— - __ (N) TEMPERED GLASS &TRIM AREAS IN LIVING ROOM (E) HEAT REG / DUCT - fSIMILAR: 9 IF WITHIN 18" OF (N) FLOOR RAISE TO (N) FLOOR LEVEL (TYP. WHERE OCCURS) 1 A2 � L ` (E) GAS METER - (E) GAS METER # Description DATE w �- (E) (E) (E) 2/0X5/0 4/0X5/0 2/0X5/0 22" OFF FLOOR PORCH PORCH - J 1 X6 SLEE ER / J 16'-4" (N) 6"X 14"UNDERFLOOR VENT OPENING TO (E) CRAWL SPACE (TYP. FOR 4) (E) (E)(E) UNDERFLOOR VENTILATION El 11 1:1 El2 UNDER FLOOR AREA = 271 S.F. _ 150= 6A2 1.8 S.F. VENT AREA REQUIRED SIMILAR: CUT (4) 6" X 14" VENT OPEING5 SHEET TITLE: THRU (E) 5UI3FLOORTO PROVIDE 2.32 S.F. VENTAREA. 1 ST STORY REMODEL LIVING ROOM RA15ED FLOOR PLAN LIVING ROOM REMODEL PLAN EX15TING LIVING ROOM PLAN DATE: 03/06/17 SCALE: 1/4" = 1'-0" SHEET: A-2 CUPERTINO 0 2' 4' 6' 8' 16' Building Department Reviewed By:Arnold Horn Date: 03/20/17 Reviewed By:Arnold Horn Date: 03/20/17 EGRE55 REQUIREMENT5 C & D Freitas ELECTRICAL SYMBOL LEGEND ALL ESCAPE OR RESCUE WINDOWS SHALL HAVE A MINIMUM NET CLEAR OPENABLE AREA OF N. Construction, Inc. SYMBOL DESCRIPTION 77[SYMBOLF DESCRIPTION 5.7 SQUARE FEET. THE MINIMUM NET CLEAR OPENA13LE HEIGHT DIMEN51ON SHALL BE 24 INCHES. THE MINIMUM NET CLEAR OPENA13LE WIDTH DIMEN51ON SHALL BE 20 INCHES. DUPLEX RECEPTACLE SURFACE MOUNTED LIGHT 0 WHEN WINDOWS ARE PROVIDED A5 A MEANS OF ESCAPE OR RESCUE THEY SHALL HAVE A LED FIXTURE FINI5HED SILL HEIGHT NOT MORE THAN 44 INCHES ABOVE THE FLOOR. W. E. Fine Q u a I I + ly HOT DUPLEX RECEPTACLE WALL BRACKET LED LIGHT FIXTURE EGRESS DOOR5 SHALL BE READILY OPENA13LE FROM INSIDE WITHOUT USE OF KEY OR 0713 Home Building SPECIAL KNOWLEDGE OR EFFORT. 220V. RECEPTACLE RECESSED LED O LIGHT FIXTURE 5• for over 45 years 220v BATHTUB AND SHOWER TILED WALLS WATERPROOF DUPLEX STEM OR SWAG LIGHT RECEPTACLE LED FIXTURE SHOWER AND TUB/SHOWER WALLS TO BE CERAMIC TILE OR OTHER SMOOTH NON W.P. HARD DUPLEX RECEPTACLE ABOVE EXTERIOR LED A135ORBENT SURFACE MTL. SET ON MORTAR OR DRY-5ET ON 1/2" TILE BACKERBOARD 23620 Morrell Road COUNTER HEIGHT OEX• LIGHT FIXTURE OVER 15# FELT OR EQ. M015TURE RE515TANT UNDER LAY +72" (MIN) ABOVE DRAIN INLET. LOS Gatos, CA 95033 NOTE: WATER RESISTANT GYPSUM BOARD SHALL BE USED OVER A CLA55 I OR II VAPOR Phone (408) 353-1900 Fax (408) 353-2209 -. JUNCTION BOX BELOW JUNCTION BOX lJJ COUNTER LINE RETARDER IN SHOWER OR BATHTUB COMPARTMENTS. WWW.freitasconstruction.com License #6286517 GROUND FAULT CIRCUIT FLUORESCENT LIGHT GFCI INTERCEPTOR FIXTURE This drawing, file and the design shown is the property of the designer. The reproduction, copy or use of this drawing or any portion thereof ARC FAULT CIRCUIT EXHAUST FAN without consent is prohibited anactionngement will be subject to legal AFC I INTERCEPTOR ® SWITCH T.V. TELEVISION OUTLET DIMMER SWITCHRECESSED FLUORESCENT OR D . LED FIXTURE NOTE: FIELD VERIFY EX15TING SMOKE ALARMS AT 3 WAY SWITCH FLUORESCENT STRIP LIGHT FIXTURE ALL SLEEPING ROOM 5, ADJACET HALLWAYS & AT 3 STAIRS PER 2016 CRC, INSTALL IF NOT EXISTING aCHIMES AND PUSH BUTTON CIRCUIT BREAKER PANEL PROVIDE CARBON MONOXIDE[) DETECTOR5, IF NOT K r i s h i n a& P h a n n i EXISTING. viswanadham O THERMOSTAT O FLOOR OUTLET 3'-9" 4'-91/2" 5-4" 12'-2" 1'-81/2" 20697 Fargo Drive SMOKE ALARM RM AND DETECTOR CARBON MONOXIDE - I IOV. O DETECTOR 2'-0" (E) WINDOW TO BE MIN. Cupertino, CA RE -GLAZED WITH NOTE: LED & FLOURE5ENT LIGHTING FIXTURES SHALL BE HIGH EFFICACY RATED. TEMP. OBSCURED GLA55 11 GENERAL NOTES SEAT L J( ELOCAT E) REG LINEN14 IFCI O O REG. 3 NICHE R:C� r - 1. LAYOUTS SHOWN ARE SCHEMATIC. LED (E) 42 HIGH o 6-7 �� o 2. ELECTRICAL AND MECHANICAL WORK SHALL COMPLY WITH ALL APPLICABLE CODES,ORDINANCES AND ENERGY SHOWER COMPLIANCE TITLES AND REQUIREMENTS. RAILING N �ED � �, r - x 3'-10" �, 3. INSTALLATION INSTRUCTIONS FOR ALL LISTED EQUIPMENT SHALL BE PROVIDED TO THE BUILDING INSPECTOR LLIO O 2/2 PKT DR. RELOCATED i T WP T O 0 AT ROUGH INSPECTION. 4. ANNULAR SPACES AROUND PIPES, ELECTRICAL CABLES, CONDUITS AND OTHER OPENINGS IN PLATES AT EXTERIOR WALLS SHALL BE PROTECTED AGAINST THE PASSAGE OF RODENTS BY CLOSING SUCH OPENINGS WITH MORTAR, MASONRY, METHOD TO THE [ ] _ QLE LED RE ED (E) X. FAN ]� - (E) 8'-O" T 1 CAR T' + O N CEILING HT. `� CEMENT CONCRETE OR SIMILAR ACCEPTABLE CITY OF LOS ALTOS. CEILING HT.' 8'"0 �p i� HOWE [CAR] 5. AN OPERATION AND MAINTENANCE MANUAL SHALL BE PROVIDED TO THE BUILDING OCCUPANT OR OWNER PER CEILING HT. THE CGBSC 4.410.1 AT THE TIME OF FINAL INSPECTION. .8® GFCI 0 0 o 'U ELECTRICAL NOTES H �� P 43� 0 V.- Z � N ~ 1. ELECTRICAL CONTRACTOR SHALL CONFIRM ALL APPLIANCE AND EQUIPMENT CHARACTERISTICS, ROUGH -IN (N) IF NOT (E) SHOWER DOOR I/ l 7_ 7 N o 2-2" = O DIMENSIONS AND CONNECTION REQUIREMENTS AND SHALL ALSO CON NECT ALL APPLIANCES AND EQUIPMENT TO OPENING MUST BE A z MIN. 22 CLEAR (N) WALK-IN WARD. z X COMPLETE OPERATING CONDITIONS. 2. NEW RECEPTACLES SHALL BE TAMPER-RESISTANT PER CEC SEC. 406.11. 3. ALL ELECTRICAL WORK AND MATERIALS SHALL CONFORM TO THE 2016 CALIFORNIA ELECTRICAL CODE. -INCHES WITH DOOR IN FULLY (N) 2/8 L OPEN POSITION, PER E O LED O o � LU O J O O 4. RECESSED LIGHTS IN INSULATED CEILING SHALL BE I.C. RATED AND AIR TIGHT A.T. RATED. SECTION 408.5 OF 5. RECEPTACLE OUTLETS IN ALL ROOMS, EXCEPT KITCHENS, TOILET ROOMS, LAUNDRY ROOMS, AND GARAGES, SHALL 2016 CPC(E) BE PROTECTED BY ARC -FAULT CIRCUIT INTERRUPTERS (AFCI), LISTED TO PROTECT ENTIRE BRANCH CIRCUIT. CEC r r _ LED p r � SEC. 210.12 (B) INCLUDES ANY CHANGES TO (E) CIRCUIT CEILING HT. �� �D 6. A DEDICATED 20 AMP CIRCUIT IS REQUIRED TO SERVE THE REQUIRED BATHROOM OUTLETS. THESE CIRCUITS (N) CANNOT SUPPLY ANY OTHER RECEPTACLES, LIGHTS, FANS, ETC.. (EXCEPTION - WHERE THE CIRCUIT SUPPLIES A I J SINGLE BATHROOM, OUTLETS FOR OTHER EQUIPMENT WITHIN THE SAME BATHROOM SHALL BE PERMITTED TO BE �{ tl O � SUPPLIED.) C.E.C. ARTICLES 210.11(C)(3) & 210.52. I 7. ALL NEW SMOKE ALARMS SHALL BE HARD -WIRED ON A LIGHTING CIRCUIT AC/DC INTERCONNECTED 120 VOLT AND HAVE BATTERY BACKUP. PER 2016 CBC 907.2.11,.11.8,.11.15 &.11.16. SMOKE ALARMS SHALL BE REPLACED AFTER - - - - - - - - - RELOCATED p - - - - - 10 YEARS FROM DATE OF MANUFACTERED PER CRC R314.3.2. SMOKE ALARMS SHALL BE UL217 LISTED w ( N) (N) 4X8 8. ELECTRICIAN SHALL FIELD VERIFY LOCATIONS OF ALL OUTLETS, LIGHT FIXTURES AND SWITCHES WITH OWNERS INTERCOM } O � DF#2 3 N 5'-6" 3'-5" 5'-3 1/2" 5'-6" PRIOR TO STARTING WORK. 9. ALL LIGHTING SHALL BE HIGH EFFICACY (FLORESCENT, LED), LED LIGHTING SYSTEM AND GU -24 LAMP HOLDER LL LL Z 5Y5TEM >- E O =O FLUSH HDR. i�!' LLo LL d SHALL BE LISTED BY ENERGY COMMISSION AND SHALL MEET THE REQUIREMENT OF TABLE 150-5 N v (E) FLUE CHASE O WATTS LUMENS/WATTS p W o LU v Z 5 OR LESS 30 >5 TO 15 40 w LL w v LL 3'-9 1 /2 " LL >15 TO 40 50 OVER 40 60 MASTER BEDROOM EDT.V. MASTER BEDROOM 10. CARBON MONOXIDE ALARMS SHALL BE LISTED AS COMPLYING W/ UL2034 AND BE INSTALLED AND MAINTAINED IN VAULTED CEILING VAULTED CEILING ACCORDANCE WITH NFPA720AND MFG. INSTRUCTIONS, CRC R315. NO CHANGE EXCEPT A5 NOTED 15T STORY OUTLINE PLUMBING NOTES q 1. ALL PLUMBING WORK AND MATERIALS SHALL CONFORM TO 2016 EDITION CALIFORNIA PLUMBING CODE. 2. HOTAND COLD WATER PIPES SHALL BE TYPE "L" COPPER, ABOVE GROUND, WITH SOLDERED JOINTS. PATCH &REFIN15H 3. DMV PIPES SHALL BE NO -HUB CAST IRON WITH NEOPRENE CONNECTORS OR ABS WITH SOLVENT CEMENT JOINTS. NOTE: VERTICAL WASTE LINES TO BE NO -HUB CAST IRON IF ABS PIPES ARE USED FOR DWV SYSTEM. FLOOR, WALLS & CEILING 4. SHOWERS AND TUB -SHOWER COMBINATIONS SHALL BE PROVIDED WITH INDIVIDUAL CONTROL VALVES OF THE PRESSURE TO MATCH (E) FIRE SPRINKLER BALANCE OR THE THERMOSTATIC MIXING VALVE TYPE. HANDLE POSITION STOPS SHALL BE PROVIDED ON SUCH VALVES (TYP.)Q AND SHALL BE ADJUSTED PER MANUFACTURE'S INSTRUCTIONS TO DELIVER A MAXIMUM MIXED WATER SETTINGS OF 120 DEGREES F. REMOVE (E) FIREPLACE < WATER CLOSETS 1.28 GALLONS/FLUSH i > (E) ELECTRIC FIREPLACE ----- -_ SHOWER HEADS 2.0 GPM LAV FAUCETS 1.2. GPM (MAX.) @ 60 PSI & 0.8 GMP (MIN.) @ 20 PSI. KITCHEN FAUCET 1.8 GPM r � L J MECHANICAL NOTES 1. ALL MECHANICAL WORK SHALL CONFORM TO 2016 EDITION CALIFORNIA MECHANICAL CODE. INSULATE SUPPLY AND RETURN DUCTS OUTSIDE CONDITIONED SPACE. 2. TERMINATION OFALL ENVIRONMENTAL AIR DUCTS SHALL BEA MINIMUM OF 3 FEET FROM ANY (E) FIELD VERITY EGRESS OPG. 6/OX4/68L. REVISIONS; OPENINGS INTO THE BUILDING (i.e. DRYERS, BATH AND UTILITY FANS, ETC., MUST BE 3 FEET AWAY FROM DOORS, WINDOWS, OPENING SKYLIGHTS OR ATTIC VENTS). PER CMC 504.5. 3. ALLAIR DUCTS PENETRATING SEPARATION WALL OR CEILING BETWEEN GARAGE AND LIVING AREA SHALL BE 26 GA. MINIMUM PER 2016 CRC. Description p DATE 4. ALL BATHROOM EXHAUST FANS SHALL BE ENERGY STAR COMPLIANT, DUCTED TO TERMINATE OUTSIDE OF THE BUILDING, AND UNLESS IT IS FUNCTIONING AS A COMPONENT OF A WHOLE HOUSE VENTILATION SYSTEM, THESE FANS MUST BE CONTROLLED BY READILY ACCESSIBLE HUMIDISTAT CAPABLE OF ADJUSTMENT BETWEEN A HUMIDITY RANGE OF 50 TO 80 PERCENT, CGBSC SECTION 4.506.1 5. HEATING AND AIR CONDITIONING SYSTEMS SHALL BE SIZED, DESIGNED, AND HAVE THEIR EQUIPEMENT SELECTED PER THE REQUIREMENTS OF THE SECTION 4.507.2 OF THE 2016 CALIFORNIA GREEN BUILDING STANDARDS CODE. 6. HVAC SYSTEM INSTALLERS SHALL BE TRAINED AND CERTIFIED PER SECTION 702 OF THE 2016 CALIFORNIA GREEN BUILDING STANDARDS CODE. SHEET TITLE: 2ND STORYATH REMODEL MASTED BEDROOM & BATH EXISTING MASTED BEDROOM & B REMODEL PLAN Legend DATE: 03/06/17 EXISTING WALLS TO REMAIN 17117_ EXISTING WALLS REMOVED NEW WALLS (E) EXISTING SCALE: 1/4" = 1'-0" (N) NEW O TEMPERED GLA55 O EGRE55 WINDOW SHEET: A-3 CUPERTINO 0 2' 4' 6' 8' 16' Building Department Reviewed By:Arnold Horn Date: 03/20/17 SECTION 4.304 LANDSCAPE IRRIGATION A. Controllers shall be weather -or soil moisture -based controllers, that automatically adjust irrigation in response to changes in plants' needs as weather condition change. B. Weather -based controllers without integral rain sensors or communication systems that account for local rainfall shall have a separate wired or wireless rain sensor which connects or communicates with the controller. 5ECTION 4.406 ANNULAR 5PACE5 Annular spaces around pipes, electric cables, conduits or other openings in sole / bottom plates at exterior walls shall be protected against the passage of rodents by closing such opening with cement mortar, concrete masonry, or similar acceptable methods. 5ECTION 4.504 POLLUTANT CONTROL 4.504.1 Covering of duct openings and protection of mechanical equipment during construction. At the time of rough installation or during storage on the construction site and until final startup of th heating and cooling equipment, all duct and other related air distribution component openings shall be covered with tape, plastic, sheetmetal or other methods acceptable to the enforcing agency to reduce the amount of dust or debris which may collect in the system. HVAC Component Protection: All duct and other related air distribution component openings shall be covered with tape, plastic, sheet metal, or other acceptable methods at the time or rough installation or during storage on the construction site and until final startup of the heating and cooling equipment. 4.504.2 Finish material pollutant control. Finish materials shall comply with this section. 4.504.2.1 Adhesives, sealants and caulks. Adhesives, sealants and caulks used on the project shall meet the requirements of the following standards unless more stringent local or regional air pollution or air quality management district rules apply. 1. Adhesives, adhesive bonding primers, adhesive primers, sealants, sealant primers, and caulks shall comply with local or regional air pollution control or air quality management district rules where applicable or 5CAQMD rule 1 168 VOC limits, as shown in Table 4.504.1 or 4.504.2, as applicable. Such product also shall comply with the Rule 1 168 prohibition on the use of certain toxic componds (chloroform, ethylene dichloride, methylene chloride, perch loroethylene and trichloroethylene), except for aerosol products, as specified in Subsection 2 below. 2. Aerosol adhesives, and smaller unit sizes of adhesives, and sealant or caulking componds (in units of product, less packaging, which do not weigh more than 1 pound and do not consist of more than 16 fluid ounces) shall comply with statewide VOC standards and other requirements, including prohibitions of use of certain toxic compounds, of California Code of Regulations, Title 17, commencing with Section 94507. 4.504.2.2 Paints and coatings. Architectural paints and coatigs shall comply with VOC limits in Table 1 of the ARB Architectural Suggested Control Measure, as shown in Table 4.504.3, unless more stringent local limits apply. The VOC content limit for coatings that do not meet the definitions for the specialty coatings catergories listed in the Table 4.504.3 shall be determined by classifying the coating as a Flat, Nonflat or Nonflat-High Gloss coating, based on its gloss, as defined in subsections 4.21, 4.36, and 4.37 of the 2007 California Air Resources Board, Suggested Control Measure, and the corresponding Flat, Nonflat or Nonflat-High Gloss VOC limit in Table 4.504.3 shall apply. 4.504.2.3 Aerosol paints and coatings. Aerosol paints and coating shall meet the Product -Weighted MIR Limits for ROC in Section 94522 (a)(2) and other requirements, including prohibitions on use of certain toxic compounds and ozone depleting substances, in Sections 94522 (c)(1) and (f)(1) of California Code of Regulations, Title 17, commencing with Section 94520; and in areas under the jurisdicition of the Bay Area Air Quality Management District additionally comply with the percent VOC by weight of th product limits of Regulation 8, Rule 49. 4.504.2.4 Verification. Verification of compliance with this section shall be provided at the request of the enforcing agency. Documentation may include, but is not limited to, the following: 1. Manufacturer's product specification. 2. Field verification of on-site product containers. Prior to final inspection, a letter signed by the general contractor OR the owner/builder (for any owner/builder projects) must be provided to the Building Official certifying that all adhesives, sealants, culks, paints, coatings, aerosol paints, aerosol coatings, carpet systems (including carpeting, cushion and adhesive), resilient flooring systems, and composite wood products installed on this project are within the emission limits specified. 4.504.3 Carpet systems. All carpet installed in the building interior shall meet the testing and product requirements of one of the following: 1. Carpet and Rug Institute's Green Label Plus Program. 2. California Department of Public Health Standard Practice for the testing of VOC's (specification 01350). 3. NSF / AN51 140 at the Gold level. 4. Scientific Certifications Systems Indoor AdvantageTM Gold. 4.504.3.1 Carpet cushion. All carpet cushion installed in the building interior shall meet the requirements of the Carpet and Rug Institute Green Label program. 4.504.3.2 Carpet adhesive. All carpet adhesive shall meet the requirements of Table 4.504.1. 4.504.4 Resilient flooring systems. Where resilient flooring is installed, at least 50 percent of floor area receiving resilient flooring shall comply with the VOC emission limits defined in the Collaborative for High Performance Schools (CHP5) Low -emitting Materials List or certified under the Resilient Floor Covering Institute (RFCI) Floor5core program. 4.504.5 Composite wood products. Hardwood plywood, particleboard and medium density fiberboard composite wood products used on the interior or exterior of the building shall meet the requirements for formaldehyde as specified in ARB's Air Toxics Control Measure for Composite Wood (17 CCR 93120 et seq.) by or before the dates specified in those sections, as shown in Table 4.504.5. 4.504.5.1 Documentation. Verification of compliance with this section shall be provided as requested by the enforcing agency. Documentation shall include at least one of the following: 1. Product certifications and specifications 2. Chain of custody certifications 3. Other Methods acceptable to the enforcing agency. TABLE 4.504.5 FORMALDEHYDE LIMITS' Maximum Formaldehyde Emissions in Parts per Million PRODUCT CURRENT LIMIT JANUARY 1, 2012 JULY 1, 2012 Hardwood plywood veneer core 0.05 Outdoor carpet adhesives Wood flooring adhesive 150 Hardwood Plywood composite core 0.08 60 0.05 Particleboard Medium density fiberboard 0.09 VCT and asphalt tile adhesives 50 0.11 50 50 Thin Medium density fiberboard 0.21 0.13 100 1. Values in this table are derived from those specified by the California Air Resources Board, Air Toxics Control Measure for Composite Wood as tested in accordance with A5TM 1333-96(2002). For additional information, see California Code of Regulations, Title 17, Section 93120 through 93120.12. 2. Thin medium density fiberboard has a maximum thinkness of 8 millimeters. TABLE 4.504.1 ADHESIVE VOC LIMIT Less Water and Less Exempt Compounds in Grams per Liter ARCHITECTURAL APPLICATIONS VOC LIMIT Indoor carpet adhsives 50 Carpet pad adhesives 50 Outdoor carpet adhesives Wood flooring adhesive 150 100 Rubber floor adhesives 5ubfloor adhesives 60 50 Ceramic tile adhesives 65 VCT and asphalt tile adhesives 50 Drywall and panel adhesives Cove base adhesives 50 50 Multipurpose construction adhesives 70 Structural glazing adhesives 100 Single -ply roof membrane adhesives 250 Other adhesives not specifically listed 50 5PECIALTY APPLICATION5 350 PVC welding CPVC welding 510 490 ABS welding 325 Plastic cement welding 250 Adhesive primer for plastic 550 Contact adhesive 80 Special prupose contact adhesive 250 Structural wood member adhesive Top and trim adhesive 140 250 5UB5TRATE 5PECIFIC APPLICATIONS Mastic texture coatings Metal to metal 30 Plastic foams 50 Porous material (except wood) 50 Wood 30 Fiberglass 80 1. If an adhesive is used to bond dissimilar substrates together, the adhesive with the highest VOC content shall be allowed. 2. For additional information regarding methods to measure the VOC content specified in the table, see South Coast Air Quality Management District Rule 116.5. TABLE 4.504.2 5ealant VOC LIMIT Less Water and Less Exempt Compounds in Grams per Liter 5EALANT5 Architectural VOC LIMIT 250 Marine deck 760 300 Nonmembrane roof Roadway 250 Single -ply roof membrane 450 Other 420 5EALANT PRIMER5 400 Architectural Nonporous Porous 250 775 Modified bituminous 500 Marine deck 760 Other 750 TABLE 4.504.3 VOC CONTENT LIMIT5 FOR ARCHITECTURAL COATING523 Grams of VOC per Liter of Coating, Less Water and Less Exempt Compounds COATING CATEGORY VOC LIMIT Flat coatings 50 Nonflat coatings 100 Nonflat-high gloss coatings 150 5pecialty Coatings Aluminum roof coatings 400 Basement specialty coatings 400 Bituminous roof coatings 50 Bituminous roof primers 350 Bond breakers 350 Concrete curing compounds 350 Concrete / masonry sealers 100 Driveway sealers 50 Dry fog coatings 150 Faux finishing coatings 350 Fire resistive coatings 350 Floor coatings 100 Form -release compounds 250 Graphic arts coatings (sign paints) 500 High temperature coatings 420 Industrial maintenance coatings 250 Low solids coatings' 120 Magnesite cement coatings 450 Mastic texture coatings 100 Metallic pigmented coatings 500 Multicolor coatings 250 Pretreatment wash primers 420 Primers, sealers, and undercoaters 100 Reactive penetrating sealers 350 Recycled coatings 250 Roof coatings 50 Rust perventative coatings 400 Shellacs Clear Opaque 730 550 5pecialty primers, sealers and undercoaters Stains 350 250 Stone consolidants 450 Swimming pool coatings 340 Traffic marking coatings 100 Tub and tile refinish coatings 420 Waterproofing membranes Wood coatings 250 275 Wood perservatives 350 Zinc -rich primers 340 1. Grams of VOC per liter of coating, including water and including exempt compounds. 2. The specified limits remain in effect unless revised limits are listed in subsequent columns in the table. 3. Values in this table are derived from those specified by the California Air Resources Board. Architectural Coatings Suggested Control Measure. February 1, 2008. More information is available from the Air Resources Board. TABLE 4.303.3 5TANDARD5 FOR PLUMBING FIXTURE5 AND FIXTURE FITTING5 5ECTION 4.505 INDOOR MOISTURE CONTROL 4.505.3 Moisture content of building materials. Building materials with visible signs of water damage shall not be installed. Wall and floor framing shall not be enclosed when the framing members exceed 19 percent moisture content. Moisture content shall be verified in compliance with the following: 1. Moisture content shall be determined with either a probe -type or contact -type moisture meter. 2. Moisture readings shall be taken at a point 2 feet (610 mm) to 4 feet (1219mm) from the grade stamped end of each piece to be verified. 3. At least three random moisture readings shall be performed on wall and floor framing with documentation acceptable to the enforcing agency provided at the time of approval to enclose the wall and floor framing. Insulation products which are visibly wet or have a high moisture content shall be replaced or allowed to dry prior to enclosure in wall or floor cavities. Wet -applied insulation products shall follow the manufacturer's drying recommendations prior to enclosure. 5ECTION 4.506 INDOOR AIR QUALITY AND EXHAU5T 4.506.1 Bathroom exhaust fans. Mechanical exhaust fans which exhaust directly from bathrooms shall comply with the following: 1. Fans shall be ENERGY STAR compliant and be ducted to terminate outside the building. 2. Unless functioning as a component of a whole house ventilation system, fans must be controlled by a humidistat which shall be readily accessible. Humidistat controls shall be capable of adjustment between a relative humidity range of 50 to 80 percent. Note: For the purpose of this section, a bathroom is a room which contains a bathtub, shower or tub/shower combination. 5ECTION 4.507 ENVIRONMENTAL COMFORT 4.507.1 Openings. Whole house exhaust fans shall have insulated louvers or covers which close when the fan is off. Covers or louvers shall have a minimum insulation value of R-4.2. 4.507.2 Heating and air-conditioning system design. Heating and air-conditioning systems shall be sized, designed and have their equipment selected using the following methods: 1. The heat loss and heat gain is established according to ANSI/ACCA Manual J. 2011 (Residential Load Calcuation)A5HRAE handbooks or other equivalent design software or methods. 2. Duct systems are sized according to ansi/ACCA 29-D Manual D. 2014 (Residentail duct System) A5HRAE handbooks or other equivalent design software or methods. 3. Select heating and cooling equipment according to ACCA 36-5 Manual 5 2014 (Residential Equipment Selection) or other equivalent design software or methods. Exception: Use of alternate design temperatures necessary to ensure the systems function are acceptable. A5HRAE STANDARD 62.2 WHOLE HOU5E VENTILATION SOUND RATING AND CONTINOU5 OPERATION The whole -building ventilation exhaust fan will operate continuously, and is required to be rated for sound at a maximum of 1 sone. This fan can be controlled by a standard on/off switch, but the switch must be labeled to inform the occupant that the exhaust fan is the whole -building ventilation exhaust fan and is intended to operate continuously. No specific wording is mandated, but the wording needs to make clear what the control is for and the importance of operating the system. This may be as simple as "Ventilation Control" or might include wording such as "Operate when the house is in use" or "Keep on except when gone over 7 days" or "Fan is to be left on to ensure indoor air quality." 5ECTION 408.1 CONTRUCTION WA5TE RECYCLING MANAGEMENT 4.408.1 A minimum of 65 percent of the construction waste gererated at the site is diverted to recycle or salvage. 4.408.2 Construction Waste Management Plan. Submit a Construction Waste Management Plan in conformace w/ items 1 thru 5 of Section 4.408.2 by weight or volumn. REQUIRED 5TANDARD5 Water closets (toilets) - flushometer valve -type single ASME A 112.1 9.2/C9A 845.1 - 1.28 gal. (4.8 L) flush, maximum flush volume Fan Rating cfm 0 0.25 in w.g. Water closets (toilets) - flushometer valve -type dual A5ME A 1 12.19.14 and U.5. EPA Water5ense Tank -Type flush, maximum flush volume High Efficiency Toilet Specification - 1.28 gal. (4.8 L) Water closets (toilets) - tank type - 0.28 Gal per flush U.5. EPA Water5ense Tank -Type High Efficiency Toilet Specification Urinals, maximum flush volume A5ME A 112.1 9.2/C5A 845.1 - 0.5 gal. (1.9 L) Kitchen Faucets - 1.8 GPM @ 60 psi Diameter, (in) Public lavatory faucets: A5ME A 1 12.1 18.1 /C5A 8125.1 Maximum flow rate - 0.5 gpm (1.9 L/min) X Public metering self-closing faucets: Maximum water use - 0.25 gal (1.0 L) per metering cycle ASME A 1 12.1 18.1 /C5A 8125.1 Residential bathroom lavatory sink faucets: A5ME A 1 12.1 18.1 /C5A 13125.1 Maximum flow rate - 1.2 gpm (5.7 L/min) X NOTE: All plumbing fixtures and fittings shall meet the standards referenced in table 1401.1 of the 2016 California Plumbing Code (CPC), CGBSC Section 403.3.2 per 2013 CGBSC CUPERTINO Building Department Reviewed By:Arnold Hom Date: 03/20/17 A5HRAE 5TANDARD 62.2 TABLE 7.1 TABLE 7.1 PRESCRIPTIVE DUCT SIZING REQUIREMENTS Duct Type Flex Duct Smooth Duct Fan Rating cfm 0 0.25 in w.g. 50 80 100 125 50 80 100 125 Maximum Allowable Duct Length (ft) Diameter, (in) Flex Duct Smooth Duct 3 X X X X 5 X X X 4 70 3 X X 105 35 5 X 5 NL 70 35 20 NL 135 85 55 6 NL NL 125 95 NL NL NL 145 7 and above NL NL NL NL NL NL NL NL This table assumes no elbows. Deduct 15 ft. of allowable duct length for each turn, elbow, or fitting NL = no limit on duct length of this size. X = not allowed, any length of duct of this size with assumed turns, elbows, fittings will exceed the rated pressure drop. C & D Freitas Construction, Inc. Fine Quality Home Building for over 45 years 23620 Morrell Road Los Gatos, CA 95033 Phone (408) 353-1900 Fax (408) 353-2209 www.freitasconstruction.com License #6286517 This drawing, file and the design shown is the property of the designer. The reproduction, copy or use of this drawing or any portion thereof without consent is prohibited and infringement will be subject to legal action OWNER: Krishina & Phanni Viswanadham 20697 Fargo Drive Cupertino, CA REVISIONS: # Description DATE SHEET TITLE: MANDATORY BUILDING STANDARDS DATE: 03/06/17 SCALE: 1/4" = 1'-0" SHEET: MM